Honeywell Silent knight 5895XL Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

Honeywell Silent knight 5895XL Скачать руководство пользователя страница 26

5895XL Manual - P/N 151142-L8:L 08/09/2017

23

Flexputs™ I/O Circuits

Hardware Installation

3.5.2 Releasing Operations

Approved releasing solenoids are list in Table 3.8

Do not mix cross alarming zones with smoke verification zones. There must be at

least two automatic detection devices in each protected space. Spacing must be reduced to 0.7 times the linear spacing in accordance
with NFPA 72.

Class B Notification Wiring

You must use an appliance from the list of compatible appliances in Appendix A.

To install a Class B notification appliance circuit:

1.

Wire Class B Notification appliances as shown in Figure 3.12.

2.

Configure the circuit through programming.

Figure 3.12 Class B Notification Appliance Circuit Wiring

Class A Notification Wiring

You must use an appliance from the list of compatible appliances in the Appendix A at the back of this manual.

To install a Class A notification appliance circuit:

1.

Wire the Class A notification appliances as shown in Figure 3.13.

Table 3.8 Approved Releasing Solenoids

Manufacturer

Part Number

Rating

Current

Freq

Asco

T8210A107

24 VDC

3A max

0 Hz

8210G207

24 VDC

3A max

0 Hz

alarm polarity shown.

UL Listed EOL

4.7 k



Supervised
Power Limited

Notification Wiring

Regulated

«
...
24
25
26
27
28
...
»

Содержание Silent knight 5895XL

















































Отзывы:

Нет отзывов