manualshive.com logo in svg

Honeywell S89E, Быстрый старт, Страница: 9 / 12

Поделиться
Скачать
Honeywell S89E Скачать руководство пользователя страница 9

S89E,F DIRECT SPARK IGNITION CONTROL MODULE

9

68-0066—4

Fig. 5. Troubleshooting S89E,F.

START

REVIEW NORMAL

OPERATING SEQUENCE.

TURN GAS SUPPLY ON.

TURN THERMOSTAT UP

TO CALL FOR HEAT.

POWER TO S89 (24 VAC

AND 120 VAC NORMAL)

S89E - 10 SEC. MAX.

DELAY FOR SAFE

START CHECK

S89F ONLY—

38 SECOND MAXIMUM

VALVE-ON DELAY

SPARK ACROSS 

IGNITER GAP

MAIN BURNER LIGHTS

SPARK STOPS BEFORE

END OF IGNITER TIMING

SYSTEM RUNS UNTIL

CALL FOR HEAT ENDS

CALL FOR HEAT ENDS;

SYSTEM SHUTS OFF

TROUBLESHOOTING ENDS

CHECK LINE VOLTAGE POWER. LOW VOLTAGE TRANSFORMER, 

LIMIT CONTROLLER, THERMOSTAT AND WIRING. ALSO, AIR

PROVING SWITCH ON PREPURGE SYSTEMS (SEE WIRING HOOKUPS.)

REPLACE S89.

NO

NO

YES

YES

YES

YES

YES

YES

YES

YES

NO

NO

NO

NO

M19839A

NO

NO

CHECK SPARK

IGNITION CIRCUIT.

SEE COMPONENT

CHECKS.

SPARK OKAY?

• CHECK FOR 120V TO SPARK GENERATOR.

• REPLACE SPARK GENERATOR IF VOLTAGE OK.

• IF NO VOLTAGE, REPLACE S89.

• MAKE SURE IGNITION CABLE

  – PROVIDES ELECTRICAL CONTINUITY.

  – DOES NOT TOUCH ANY METAL SURFACES.

  – CONNECTIONS ARE METAL SURFACES.

  – SHOWS NO SIGNS OF MELTING OR BUCKLING.

     REPLACE AND SHIELD CABLE IF NECESSARY.

• MAKE SUE BURNER SPARK IGNITER AND S89 GROUND

  (BURNER) TERMINAL HAVE EFFECTIVE COMMON

  GROUND. POOR OR ERRATC GROUND WILL CAUSE

  NUISANCE SHUTDOWNS.

• CHECK FOR CRACKED INSULATOR ON IGNITER OR

  FLAME SENSOR. REPLACE DEVICE WITH CRACKED

  INSULATOR TO PREVENT SHORT TO GROUND.

NOTE:  IF S89 LOCKS OUT, RESET BEFORE CONTINUING.

• CHECK FOR 24 VAC ACROSS VALVE AND VALVE (GROUND)

   TERMINALS ON S89. IF NO VOLTAGE, REPLACE S89.

• MAKE SURE IGNITER AND SENSOR ARE PROPERLY

  POSITIONED. SEE COMPONENT CHECKS.

• CHECK ELECTRICAL CONNECTIONS BETWEEN S89 AND

  GAS CONTROL. IF OKAY, REPLACE GAS CONTROL.

NOTE:  IF S89 LOCKS OUT, RESET BEFORE CONTINUING.

• MAKE SURE FLAME CURRENT IS AT LEAST 0.8 MICRO AMPS.

  SEE COMPONENT CHECKS.  

• MAKE SURE L1 AND L2 ARE CONNECTED TO THE PROPER TERMINALS.

• MAKE SURE FLAME DOES NOT TOUCH SENSOR INSULATOR AND

  THAT SENSOR INSULATOR IS BELOW FLAME. EXCESSIVE HEAT

  (OVER 1000 F [538 C]) WILL CAUSE SHORT TO GROUND.

  RELOCATE SENSOR OR SHIELD INSULATOR IF EXCESS HEAT

  IS SUSPECTED.

• IF CHECKS ARE OKAY, REPLACE S89 MODULE.

• CHECK FOR PROPER TEMPERATURE CONTROLLER OPERATION.

• REMOVE VALVE LEAD AT S89: IF VALVE CLOSES, RECHECK

  TERMPERATURE CONTROLLER AND WIRING; IF NOT , REPLACE GAS

  CONTROL.

REPEAT PROCEDURE UNTIL TROUBLE FREE OPERATION IS OBTAINED.

REPLACE S89.

Содержание S89E













Отзывы:

Нет отзывов