Honeywell S7999B Скачать руководство пользователя страница 45

Страница: 45 / 76

S7999B SYSTEM DISPLAY

65-0283—2

PID Load Controller

Current load water temperature or steam pressure is obtained

from the UDC controller and displayed in text value and in a

bar graph on the page (see Fig. 89 and 90). Upper and lower

limits of the water temperature/steam pressure range are

displayed on the page next to the load bar graph.

Fig. 89. Steam PID Load Controller.

Fig. 90. Water Temperature Load Controller.

The control setpoint for PID modulation is obtained from UDC

controller and displayed on the page. The control setpoint can

also be adjusted on this page. The control setpoint is set by

the user using the Up Arrow and Down Arrow buttons. The

UDC controller modulates the burner control toward this target

setpoint.

Status of the On-Off relay is obtained from the UDC controller.

An LED displayed on the page indicates when demand is on

(green) or off (red).

If a Low Fire Hold alarm is configured in the UDC controller,

the setpoint of this alarm is obtained from the UDC controller

and displayed on the page. The status of the alarm is

displayed on the page with an LED that is red when Low Fire

Hold has occurred and green when the system isn’t in Low

Fire Hold.

The user can adjust the alarm setpoint of both alarms. Manual

control of the UDC controller output is also permitted by

selecting the yellow “Auto Output” button. Adjustment is

raised or lowered in 1% (0.16 mA) increments. The S7999B

System password (same as Setpoint Adjustment) is required

before manual control is permitted. After successful login, the

Up Arrow and Down Arrow buttons can be used to change the

alarm setpoints.

PID modulation output is obtained from UDC controller and

displayed on the page in text value (mA).

Feed Pump Level Controller

The current water supply level (percent full) is obtained from

the UDC controller and displayed both in text value and in a

bar graph on the page. Upper (100%) and lower (0%) limits

are displayed next to the bar graph.

Fig. 91. Feed Pump Level Controller.

Status of the Start-Stop relay in the UDC controller is

displayed on the page as an LED that is green when the relay

is in Start mode and red when the relay is in Stop mode. The

Start Pump and Stop Pump setpoints (in percent) are obtained

from the UDC controller and displayed on the page. The user

can adjust these Start Pump and Stop Pump setpoints with the

Up Arrow and Down Arrow buttons. Successful password

If a High Water alarm is configured in the UDC controller, the

setpoint of this alarm is displayed on the page. The status of

the alarm is indicated by an LED that is red when a status and

high water condition exists, and green when safe water level

exists. The user can adjust the alarm setpoint on the page.

Содержание S7999B













































































Результаты поиска

Содержание S7999B

Отзывы:

Похожие инструкции для S7999B

Бренды по названию

Популярные бренды

Honeywell S7999B, Руководство пользователя

Результаты поиска

Содержание S7999B

Отзывы:

Похожие инструкции для S7999B

Бренды по названию

Популярные бренды