Honeywell PRO3200 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 35

Honeywell PRO3200 Скачать руководство пользователя страница 8

2

www.honeywell.com

PRO3200 Installation

Notices

1 Notices

1.1 Warnings and Cautions

Note:

See the Remote Enclosure Installation Manuals PPRO22ENC1, PRO22ENC2,

PRO22ENC3 or PRO22ENC5 for installation instructions.

Before Installation

Warning:

Before installation,

TURN OFF

the external circuit breaker which supplies

power to the system.

Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply (see '

Technical Specifications

Do not apply power to the system until

after

the installation has been completed.

Personal injury or death can occur, and the equipment can be damaged beyond repair,
if this precaution is not observed.

Fire Safety and Liability Notice

Warning:

Never connect card readers to any critical entry, exit door, barrier, elevator or
gate without providing

an alternative exit

in accordance with all the fire and

life safety codes pertinent to the installation.

These fire and safety codes vary from city to city and you must get approval from
local fire officials whenever using an electronic product to control a door or other
barrier. Use of egress buttons, for example, may be illegal in some cities. In most
applications, single action exit without prior knowledge of what to do is a life safety
requirement. Always make certain that any required approvals are obtained in writing.
DO NOT ACCEPT VERBAL APPROVALS SINCE THEY ARE NOT VALID.

Honeywell never recommends using the PRO3200 or related products for use as a
primary warning or monitoring system. Primary warning or monitoring systems
should always meet the local fire and safety code requirements. The installer must also
test the system on a regular basis by instructing the end user in appropriate daily
testing procedures. Failure to test a system regularly could make the installer liable for
damages to the end user if a problem occurs.

Earth Grounding

Warning:

EARTH

ground all enclosures for proper installation.

Use Suppressors

Warning:

Use suppressors on all door strikes. Use S-4 suppressors for installation.
Honeywell recommends only DC strikes.

«
...
6
7
8
9
10
...
»

Содержание PRO3200




































Отзывы:

Нет отзывов