Honeywell PRO3200 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 35

Honeywell PRO3200 Скачать руководство пользователя страница 19

PRO3200 Installation

Setting Up the PRO3200 Hardware

PRO3200 (PRO32IC) Installation and Configuration Guide, Document 800-15494

13

3.3 Technical Specifications

Caution:

Locate the power source as close to this board as possible. Connect power with minimum of

18AWG wires.

Note:

POLARITY for 12 VDC power is important. Make sure the +12 VDC is connected to the

terminal l12V and the return is connected to the terminal labeled GND.

Table 3 PRO3200 Technical Specifications

Category

Description

WARNING: PRO3200 is manufactured for use in
low-voltage, Class 2 circuits only.

Primary Power

12Vdc nominal with an operating range of 10 to 14Vdc., 300mA
maximum.
12Vdc @ 240mA (325mA with CoBox-Micro) nominal.

Memory and
Clock Backup

3Volts Lithium, type BR2325, BR2330, CR2330.

Ports

Port 0

10Base-T/100Base-TX

Ethernet.

Port 1

RS-232 or 2-wire RS-485: 9,600 to 115,200
bps, async.

Port 2 & 3

2-wire RS-485: 2,400 to 38,400 bps, async.

Inputs

2 non-supervised, dedicated for cabinet tamper and power fault
monitoring.

Cable requirements

Power:

1 twisted pair, 18 AWG.

RS-485:

24AWG, 4,000ft (1,200m) maximum, twisted
pair with shield. 120 ohm.

RS-232:

24AWG, 25ft (7.6m) maximum.

Ethernet:

Cat

5.

Alarm input:

1 twisted pair, 30 ohms maximum.

Environmental

Temperature:

0 to 49°C, operating
-55 to +85°C, storage

Humidity:

0 to 85% RHNC

Mechanical

Dimensions:

5.5 in. (137.7mm) W x 9 in. (228.6.4mm) L
x .75 in. (19.05mm) H

Weight:

7.1 oz. (201 gm) nominal

Specifications subject to change without notice.

«
...
17
18
19
20
21
...
»

Содержание PRO3200




































Отзывы:

Нет отзывов