H4D3PRV2 True Day/Night Rugged Indoor/Outdoor IR Minidome IP Camera
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing
or damaged, contact your dealer immediately.
•
•
•
•
Camera
Documentation CD
Quick install guide
Allen key (L-wrench)
•
•
•
Self-tapping screws (×3)
Plastic wall anchors (×3)
Mounting template
2
Required tools:
•
•
A Phillips screwdriver
A drill with an appropriately-sized drill bit for pre-drilling holes for the screw anchors.
CAUTION
Installation and servicing should be performed only by qualified
and experienced technicians to conform to all local codes and to maintain your
warranty.
3
Aiming the Camera and Adjusting Zoom and Focus
1.
Aim the camera lens in the desired direction.
2.
Tighten the adjustment screws to secure the camera lens in place.
3.
Attach the dome cover to the camera and remove the protective film from the bubble.
4.
Set the lens zoom and focus.
The camera connected to a PoE port of the Honeywell Embedded NVR can be configured
with the NVR directly.
To log on to the camera with a PC, perform the following steps:
a. Install the Honeywell Config Tool from the software and the documentation CD, find the
camera and open the web browser with the Honeywell Config Tool.
b. Log on to the camera as the admin user. The default user name is
admin
(case-
sensitive) and the default password is
1234
.
c. Go to
Setup
Camera
Conditions
Zoom and Focus
. The following panel appears:
1
Preparing the Mounting Surface
1. Inspect the site where you want to install the camera. The mounting surface must be
flat and capable of supporting at least three times the weight of the camera.
2. Remove the backing from the mounting template sticker and affix the sticker to the
mounting surface.
Note
If you are using the side exit for the cable, note the orientation of the cable exit notch.
In outdoor installations the notch should point downwards to prevent water from entering
the camera housing.
Document 800-21231V1 – Rev A– 10/2015
© 2015 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
3.
Drill three screw holes at the locations indicated on
the mounting template sticker and insert the three
supplied plastic anchors in the holes.
4.
If you are flush mounting the camera and want to
store the cables inside the wall or ceiling, drill a hole
at the cable exit position on the mounting template
and then pull the cables through the hole.
Mounting the Camera
1.
Use the supplied Allen key to remove the dome cover from the camera assembly and set it
aside.
a.
Open the cover of the microSD card reader as shown in
Figure 2-1
.
b.
Place the microSD card in the reader as shown in
Figure 2-2
, and then
close the cover.
3. Connect the camera with the Ethernet cable and the power cable.
a.
Connect one end of the Ethernet cable to the RJ-45 port on the camera.
b.
If the other end of the Ethernet cable is NOT connected to a PoE (Power-over-
Ethernet) switch or NVR, connect the power connector of the camera to a 12 V DC
power source.
4. Attach the camera assembly to the mounting surface using the supplied screws.
• Click
Zoom in +
or
Zoom out –
to zoom in or out.
• Click
Near –
or
Far +
to focus near or far, or click
Auto Focus
to enable auto
focus.
2. If local storage is needed, insert a Micro SD card into the Micro SD card slot according to
the following steps:
+86 21 22196888
Figure 2-1
Figure 2-2
