10
9
12
11
TEMPERATURE AND ALARM WINDOW
The
Temperature and Alarm Window
displays an indoor
temperature and the time alarms.
TIME AND CALENDAR WINDOWS
The Color Changing Projection Clock displays time in an
hour-minutes-seconds
format in the
Time Window
located below the
Temperature and Alarm Window
.
The date is displayed in
month-date
format next to the day
of the week and moon phase icon in the
Calendar Window
.
MANUAL SETTINGS
If desired, the time, date and other available parameters
can be programmed manually.
It is necessary to set your Time Zone manually.
TIME ZONE
• Enter the US Time Zone programming mode by pressing
and holding the
UP (+)
button for 3 seconds.
• Keep holding
UP (+)
button until the desired time zone
(Pacific, Mountain, Central or Eastern) is highlighted on
the unit’s display map in the
Time Window
• Release the
UP (+)
button and the desired Time Zone
will be selected
CLOCK
• Press and hold
MODE
button for 3 seconds until the
year
digits in the
Calendar Window
will flash
• Press
UP (+)
or
DOWN (-)
adjusting a correct year
• Press
MODE
to confirm and move to the next parameter
– the month digit will flash
• Press
UP (+)
or
DOWN (-)
adjusting the current
month
and then press
MODE
to confirm – the date digit will flash
ATOMIC CLOCK
Immediately after batteries installation, the clock will beep
and display all available LCD segments for a moment.
Immediately after the atomic time signal receiver will start
searching for the atomic time signal. It usually takes
between 5-8 minutes.
NOTE: Do not press any buttons on the unit during
auto search as it may interrupt product’s operation,
and you will need to start the set up procedure again.
If the reception is successful and the atomic time signal is
received, the date and time will be set automatically, and
the [ ] icon will appear on the display.
NOTE: It is necessary to set your Time Zone, having in
mind that the default zone is a Pacific Standard Time
(PST). (
Refer to a
MANUAL SETTINGS
section
)
If the initial reception was not successful and the time
signal has not been received in this first 8 minutes, you
may use the
MODE
button to set the time and date
manually. (Refer to the
MANUAL SETTINGS
section).
After the clock is set manually, place it by the window for
the better reception. The atomic time receiver is programmed
that it will continue to search for the atomic time signal
daily for every hour between 1:00 am and 4:30 am.
NOTE: At the time of the initial reception allow at least
24 hours for the atomic time receiver to pick up the
signal. In some cases, depending on the location, it may
take up to 72 hours.
Once the time signal has been successfully received, the
time and the date will be updated automatically.
station. If the tower icon is not fully lit, or if the time and
date are not set automatically, please consider the
following:
• During night-time hours, atmospheric disturbances are
typically less severe and radio signal reception may
improve. A single daily reception is sufficient enough to
keep the clock accuracy within 1 second.
• Make sure the unit is positioned at 8 feet (2 meters)
distance from any interference source such as a TV,
computer monitor, microwave, etc.
Within concrete wall rooms such as basements or office
buildings, the received signal may be weakened. Always
place the Color Changing Projection Clock near the
window for better reception.
• Press
UP (+)
or
DOWN (-)
adjusting the date and then
press
MODE
to confirm – the hour digit will flash in the
Time Window
• Press
UP (+)
or
DOWN (-)
adjusting the hour and then
press
MODE
to confirm – the
minutes
will flash
• Press
UP (+)
or
DOWN (-)
adjusting the minutes and
then press
MODE
to confirm – the temperature in the
Temperature and Alarm Window
will flash
• Press
UP (+)
or
DOWN (-)
selecting the temperature
unit in Fahrenheit or Celsius
• Press
MODE
for the last time to confirm after the last
parameter is set
DAY OF THE WEEK LANGUAGE
• Press and hold
DOWN (-)
button for 3 seconds to enter
into the day of the week language programming mode:
the default language abbreviation will appear (example –
EN
)
• Continue holding
DOWN (-)
button until the desired day
of the week language abbreviation is displayed
• Release the
DOWN (-)
button and the day of the week
will be displayed in selected language
ALARMS
The Color Changing Projection Clock has two time alarms.
If any of the alarms is activated, it will sound at the set
time and the alarm icon will flash.