Honeywell P531 страница 27 Скачать руководство пользователя

Страница: 27 / 27

Page 24

MODELS P531, P532 AND P532UI OPERATING MANUAL

RS-232 (P531 front panel port only)

Baud

19200

Parity

None

Protocol

Modbus(RTU) fixed address of 64

Flame

Maximum flame detector response time

5 second

Minimum flame detector self-checking rate

1 second

Maximum flame failure “lock-out” time

2 to 4 seconds (adjustable)

Maximum flame failure response time

2 to 4 seconds (adjustable)

Signal for presence of flame

Flame on set point (adjustable)

Signal for absence of flame

Flame off set point (adjustable)

No large Maximum flame signal will cause lost flame indication.

Compatibility

Viewing head #3

S702, S706, S802 or S806 (and -PH and –HF versions)

Viewing head #1 or #2

S550x, S552x, S556x (and –PF versions)

Fuses

No user serviceable components are inside.

Self-resetting fuses are provided internally on the following connections:

+24 PWR DC input voltage supply (DC units only)

+24 BATT Battery input voltage supply

These require cooling off period (of no load) to reset.

Cleaning

Turn power off before cleaning.

Only wipe Panel front with a soft cloth (dry or slightly dampened with water).

Cable

Connection from the Signal processor to the viewing heads shall use approved cable:

Cable can be Instrument Tray cable with CIC C22.2 No. 239 certification C330

Or must be run inside of Conduit (with properly sealed ends).

Environmental

Ambient Temperature

-40° C to 60° C (FM) or 0° C to 52° C (CSA)

Humidity

non-condensing

Maximum 80% for temperatures below 31° C Decreasing to

50% maximum at 40° C and above

Vibration

+1 g at 10 to 150 Hz

Rev.0405

maxon.su

Содержание P531




























Результаты поиска

Содержание P531

Отзывы:

Похожие инструкции для P531

Бренды по названию

Популярные бренды

Honeywell P531, Руководство по эксплуатации

Результаты поиска

Содержание P531

Отзывы:

Похожие инструкции для P531

Бренды по названию

Популярные бренды