Honeywell NOTIFIER UDACT-2 Скачать руководство пользователя страница 33

Страница: 33 / 52

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

Section 6: Compatible UL Listed Receivers

6.1 UL Listed Receivers

The chart below shows UL listed receivers compatible with the UDACT-2. A check in the protocol column indicates the receiver sup-
ports that protocol.

Receiver

4+2

Standard

1800/2300

Ademco

Contact

SIA

Ademco 685 (1)



Ademco MX8000 (2)



Silent Knight 9500 (3)



Silent Knight 9800 (4)



FBI CP220FB (5)



Osborne Hoffman 2000E (6)



Radionics 6600 (7)



SurGard MLR2 (8)



SurGard System III (9)



SurGard MLR-2000 (10)



Table 6.1 Compatible UL Listed Receivers

NOTE:

(1) With 685-8 Line Card with Rev 4.4d software.

(2) With 124060V206B and 124063 Line Card Rev. B.

(3) With version V2.4 Receiver and 126047 Line Card Rev G.

(4) With 124077V2.00 Receiver and 126047 Line Card Rev M.

(5) With software V3.9.

(6) With V.7301 Receiver S/W.

(7) With 01.01.03 Receiver S/W and Line Card 01.01.03.

(8) With software V1.86.

(9) With software V1.72.

(10) With DSP4016 and V1.6 Line Card.

Содержание NOTIFIER UDACT-2





















































Результаты поиска

Содержание NOTIFIER UDACT-2

Отзывы:

Похожие инструкции для NOTIFIER UDACT-2

Бренды по названию

Популярные бренды

Honeywell NOTIFIER UDACT-2, Инструкция по эксплуатации

Результаты поиска

Содержание NOTIFIER UDACT-2

Отзывы:

Похожие инструкции для NOTIFIER UDACT-2

Бренды по названию

Популярные бренды