Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 110

Страница: 110 / 210

110

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

Dedicated Smoke Control System Wiring Diagrams

Figure 5.3 Fan Control, Dedicated System - FSCS Switch Group Type 4

Figure 5.3 depicts a fan in a dedicated system with the capability of

control and verification of the

OFF

state, switch group type 4. In the

above configuration, the CON

ON⁄OP

CM is deactivated. The CON

ON⁄OP

CM controls a normally open contact which switches power to the fan

(the contact is used when the power being switched is greater than 24 volts). When the CON

ON⁄OP

CM is deactivated, the contact is open,

thus cutting power to the fan. When power is cut to the fan, the fan is

OFF

and the sail switch is

CLOSED

, indicating no airflow in the duct. The

VER

OFF⁄CL

MM monitors the

CLOSED

position of the sail switch, which would indicate when the fan is

OFF

. In this case the VER

OFF⁄CL

is activated because the fan is

OFF

and the sail switch is

CLOSED

Power Source

1b listed
contactor

Service
Disconnect
Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed

Sail

Switch

N/O

COM

N/C

Power Return

Listed

24 VDC

Power Source

FMM-1

FCM-1

CON

ON⁄OP

(deactivated)

VER

OFF/CL

(activated)

N-

Df4-fs-2

.wmf

SLC Loop

FAN OFF

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 110 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: