Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 61

Страница: 61 / 68

LDM Series Instruction Manual —

P/N 15885:H3 8/12/2019

Configuration for the LDM-32 and AFP-200

AFP-200 (UL 8th)

Alarm and Trouble Mode With 8-Point Shift

It is assumed that systems with 8-Point Shift selected will be 56 zones or less.

Table E.1 LDM Series Switch Control Functions

Figure E.1 illustrates configuration of the LDM to annunciate the Active state of all 99 software zones (no zone troubles) with the first
eight points (P1 through P8) dedicated to the AFP-200 system function LEDs listed below.

LDM Switch Position

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

not used

ACK

not used

SIG.SIL.

not used

RESET

not used

DRILL

not used

OUTPUTS

Address #1

LDM-32

LDM-E32

System Functions *

25 - 32

1 - 8

33 - 40

9 - 16

41 - 48

17 - 24
49 - 56

Address #2

LDM-32

LDM-E32

57 - 64
89 - 96

65 - 72
97 - 99

73 - 80

81 - 88

* System Status Indicators

System Alarm

not used

View of LDM-32

wire to
LEDs

Figure E.1 Display Active Status of Software Zones Only

* It is assumed this mod-
ule/expander annunciates zones
65-99 and is not functioning as a
'Receive Only' annunciator.

Содержание NOTIFIER LDM Series





































































Результаты поиска

Содержание NOTIFIER LDM Series

Отзывы:

Honeywell NOTIFIER LDM Series, Инструкция по эксплуатации, Страница: 61 / 68

Результаты поиска

Содержание NOTIFIER LDM Series

Отзывы: