Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 68

Honeywell NOTIFIER LDM Series Скачать руководство пользователя страница 54

54

LDM Series Instruction Manual —

P/N 15885:H3 8/12/2019

AFP-100 (UL 8th)

Configuration for the LDM-32 and AFP-100

Figure D.3 illustrates wiring the LDM to annunciate the active and trouble states for all 56 zones with the first eight points (J5: P1
through P8 and J6: P1 through P8) dedicated to AFP-100 functions.

Figure D.4 illustrates configuration for the LDM to annunciate active and trouble states for the first 56 software zones with the last eight
points (16 LEDs) dedicated to the AFP-100 functions listed below.

It is assumed that the '8-Point Shift' will be selected only on systems containing less than 56 zones/points.

J6

J5

OUTPUTS

J7

J8

Alarm

Alarm

Alarm

Alarm

Trouble

Trouble

Trouble

Trouble

J6

J5

OUTPUTS

Address #1

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

System Status Indicators*

13 - 16
29 - 32
45 - 48

1 - 4

17 -   20
33 -   36
49 -   52

5 - 8

21 - 24
37 - 40
53 - 56

9 - 12

25 - 28
41 - 44

view of LDM-32

* System Status Indicators

not used
not used
not used
not used
Supervisory (Yellow LED)

not used
not used
AC Fail (Yellow LED)

not used

not

used

Signals Silenced (Yellow LED)

System Trouble (Yellow LED)

System Alarm (Red LED)

not

Figure D.3 Alarm/Trouble Annunciation of 56 Software Zones Without 8-Point Shift

J6

J5

OUTPUTS

J7

J8

Alarm

Alarm

Alarm

Alarm

Trouble

Trouble

Trouble

Trouble

J8

J7

OUTPUTS

Address #1

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

System Status Indicators*

13 - 16
29 - 32
45 - 48

1 - 4

17 - 20
33 - 36
49 - 52

5 - 8

21 -   24
37 -   40
53 -   56

9 - 12

25 - 28
41 - 44

view of LDM-32

* System Status Indicators

not used
not used
not used

not used
Supervisory (Yellow LED)
not used
not used
AC Fail (Yellow LED)

not used
not used

Signals Silenced (Yellow LED)

System Trouble (Yellow LED)

System Alarm (Red LED)

not

Figure D.4 Alarm/Trouble Annunciation of 56 Software Zones With 8-Point Shift

«
...
52
53
54
55
56
...
»

Содержание NOTIFIER LDM Series





































































Отзывы:

Нет отзывов