Page 2 of 2 — dn-6936:a1 • 06/8/09
Notifier® and FlashScan® are a registered trademark of Honeywell International Inc.
Bayblend® is a registered trademark of Bayer Corp.
©2009 by Honeywell International Inc. All rights reserved. Unauthorized use of this docu-
ment is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Made in the U.S. A.
vides detailed information on detector spacing, placement,
zoning, wiring, and special applications.
Installation
The FST Series plug-in intelligent thermal detector uses a sep-
arate base to simplify installation, service, and maintenance.
Installation instructions are shipped with each detector.
Mount base (all base types) on an electrical backbox which is
at least 1.5" (3.81 cm) deep. Suitable boxes include:
• 4.0" (10.16 cm) square box.
• 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box.
• Single-gang box (except relay or isolator base).
• With B501BH-2 or B501BHT-2 base, use a 4.0" (10.16 cm)
square box.
• With B224RB or B224BI base, use a 3.5" (8.89 cm) or 4.0"
(10.16 cm) octagonal box, or a 4.0" (10.16 cm) square box.
NOTE: 1)
Because of the inherent supervision provided by the
SLC loop, end-of-line resistors are not required. Wiring “T-taps” or
branches are permitted for Style 4 (Class “B”) wiring.
2)
When
using relay or sounder bases, consult data sheet DN-2243 (ISO-X)
for device limitations between isolator modules and isolator bases.
Agency Listings and Approvals
These listings and approvals apply to the modules specified in
this document. In some cases, certain modules or applications
may not be listed by certain approval agencies, or listing may
be in process.
Consult factory for latest listing status.
•
UL Listed:
S747
•
ULC Listed:
S6978
MEA Listed:
383-02-E
• FM Approved
•
CSFM:
7270-0028:196
•
BSMI:
CI313066760025
•
CCCF:
Certif. # 2004081801000018
•
U.S. Coast Guard:
161.002/23/3 (AFP-200); 161.002/27/3
(AFP1010/AM2020); 161.002/42/1 (NFS-640)
•
Lloyd’s Register:
03/60011
Product Line Information
“A” suffix indicates ULC Listed model.
FST-851:
Intelligent thermal detector. Must be mounted to one
of the bases listed below.
FST-851A:
Same as FST-851 but with ULC Listing.
FST-851R:
Intelligent thermal detector with rate-of-rise feature.
FST-851RA
: Same as FST-851R but with ULC Listing.
FST-851H:
Intelligent high-temperature thermal detector.
FST-851HA:
Same as FST-851H but with ULC Listing.
BASES:
B710LP:
Standard U.S. low-profile base
B710LPBP:
Standard U.S. low-profile base, pkg. of 10.
B710LP:
Standard U.S. low-profile base.
B710LP(A):
Standard U.S. low-profile base.
B501BP:
Standard European flangeless base, pkg. of 10.
B501:
Standard European flangeless base.
B501(A):
Standard European flangeless base, ULC Listing.
BH501BH-2:
Sounder base, includes
B501
base above.
BH501BHT-2:
Same as B501BH-2, but includes temporal sounder.
BH501BHA:
Sounder base, includes
B501
base above
BH501BHTA
: Same as BH501BHA, but includes temporal sounder.
B224BI(A):
Intelligent isolator base. Isolates SLC from loop
shorts.
ACCESSORIES:
F110:
Retrofit replacement flange for older style high profile
bases. Converts bases for use with FlashScan® detectors.
RA400Z(A):
Remote LED annunciator. 3 – 32 VDC. Fits U.S.
single-gang electrical box. Supported by B710LPBP(A) and
B501(A) bases only.
SMK400E:
Surface mounting kit provides for entry of surface
wiring conduit. For use with B501(A) base only.
RMK400:
Recessed mounting kit. For use with B501(A) base
only.
SMB600:
Surface mounting kit for use with B710LPBP(A).
BCK-200B:
Black detector covers, box of 10.
M02-04-00:
Test magnet.
M02-09-00:
Test magnet with telescope stick.
XR2B:
Detector removal tool. Allows installation and/or
removal of FlashScan® Series detector heads from base in
high ceiling installations.
T55-127-010:
Detector removal tool without pole.
XP-4:
Extension pole for XR2B. Comes in three 5-ft. sections.
