Honeywell MiniZone EMM-3U Скачать руководство пользователя страница 1

PRODUCT DATA

68-0237-2

® U.S. Registered Trademark
Copyright © 2002 Honeywell •  All Rights Reserved 

EMM-3U Universal

Electronic MiniZone™ Panel

APPLICATION

The EMM-3U Universal Electronic MiniZone™ Panel controls 

single-stage, multi-stage, conventional or heat pump heat/cool 

equipment and is used on two- and three-zone applications.

FEATURES

• Compatible with single-stage, multi-stage, 

conventional or heat pump applications.

• Uses virtually any Honeywell four-wire, single-stage, 

multi-stage, or Trol-A-Temp heat pump thermostat.

• Optional Discharge Air Temperature Sensor for 

capacity control with adjustable high and low limits.

• System and Zone LEDs indicate system status.
• Automatic zone changeover with 20-minute 

changeover timer.

• Individual zone fan control.
• Thermal circuit breaker protects panel and transformer 

from damage if miswired.

• Purge timer protects equipment between calls for 

heating and cooling.

• Uses spring-open/power-closed, spring-closed/power-

open, and power-open/power-closed dampers.

• Single or dual transformer equipment compatible.

For Internet access:

www.honeywellzoning.com

For technical support, call 1-800-828-8367.

To download Zoning literature: http://hbctechlit.honeywell.com

Contents

Application ........................................................................

1

Features ...........................................................................

1

Specifications ...................................................................

2

Ordering Information  ........................................................

2

Installation ........................................................................

4

Troubleshooting ................................................................ 15

Содержание MiniZone EMM-3U

















Отзывы: