Checking Signal Strength
When choosing a suitable mounting location, check the communicator’s signal strength to ensure proper operation. For
most installations, using the module’s internal antenna, mounting the control as high as practical, and avoiding large metal
components provides adequate signal strength for proper operation. Use the “Cell Information” screen to display signal
strength (in dBm).
Select:
Security > More > Tools > [Installer Code] > Program > Comm. Diagnostics > Cell Information
Primary Site QOS Level Signal strength is displayed by a series of 1 to 5 stars (* weak to ***** strong) or “Not Present” if
there is no signal. To ensure a reliable installation at least 2 (**) stars should consistently be present.
If necessary, relocate the Control to obtain better signal strength (press Cell Information again to refresh the reading) or
install an external antenna.
Specifications
Voltage Input
5V (provided by the control panel)
Current
Idle
30mA, standby
Transmit
490mA, max transmit
Environmental
Operating
Temperature
-20ºC to +55ºC (for compliance
agency: 0ºC to +49ºC)
Storage
Temperature
-40ºC to +70ºC
Humidity
0 to 95% relative humidity, non-
condensing (for compliance agency
0% to 85%)
Antenna
•
Penta-Band diversity antennas
for LTE
•
LTE-L57V: Supports LTE Bands
13, 4 and 2
LTE-L57A/LTE-L57C: Supports
LTE Bands 12, 13, 5, 4 and 2
External Antenna Kit
CELL-ANTSMA
Important Note About External Antennas
If an external cellular radio antenna is used, the antenna may be
installed or replaced ONLY by a professional installer.
To the Installer
LTE-L57V: The external antenna gain shall not exceed 6.94 dBi for 700MHz, 6
dBi for 1700MHz and 9.01 dBi for 1900MHz. Under no conditions may an
antenna gain be used that would exceed the ERP and EIRP power limits as
specified in FCC Parts 22H, 24E and 27.
LTE-L57A, LTE-L57C: The external antenna gain shall not exceed 6.63 dBi for
700MHz & 850MHz, 6 dBi for 1700MHz and 8.51 dBi for 1900MHz. Under no
conditions may an antenna gain be used that would exceed the ERP and EIRP
power limits as specified in FCC Parts 22H, 24E and 27, or ISED RSS-130,
RSS-132, RSS-133, and RSS-139.
Support & Warranty
For the latest documentation and online support, please go to:
https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
For patent information, see www.honeywell.com/patents
MyWebTech
Warranty
Patents
FEDERAL COMMUNICATIONS COMMISSION (FCC) & ISED STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause
interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications
in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
If using an indoor antenna, have a quality outdoor antenna installed.
•
Reorient the receiving antenna until interference is reduced or eliminated.
•
Move the radio or television receiver away from the receiver/control.
•
Move the antenna leads away from any wire runs to the receiver/control.
•
Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
•
Consult the dealer or an experienced radio/TV technician for help.
ISED CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne
doit pas causer d' interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.
RF Exposure Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located
or operated in conjunction with any other transmitter except in accordance with FCC and ISED multi-transmitter product procedures.
Mise en Garde
Exposition aux Frequences Radio:
La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm
(7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les
procédures de produit multi transmetteur FCC et ISED.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
© 2017 Honeywell International Inc.
www.honeywell.com/security