Honeywell JADE W7220 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 32

Honeywell JADE W7220 Скачать руководство пользователя страница 32

JADE™ ECONOMIZER MODULE

Home and Building Technologies

In the U.S.:

Honeywell

715 Peachtree Street NE

Atlanta, GA 30308

customer.honeywell.com

® U.S. Registered Trademark
© 2018 Honeywell International Inc.
63-2700—11 M.S. Rev. 05-18
Printed in United States

By using this Honeywell literature, you agree that Honeywell will have no liability for any damages arising out of your use or
modification to, the literature. You will defend and indemnify Honeywell, its affiliates and subsidiaries, from and against any
liability, cost, or damages, including attorneys’ fees, arising out of, or resulting from, any modification to the literature by you.

TROUBLESHOOTING

Alarms

The Economizer module provides alarm messages that
display on the 2-line LCD.

NOTE:

Upon power up, the module waits 60 minutes
before checking for alarms. This allows time for
all the configured devices (e.g. sensors, actuator)
to become operational. The exception is the MA
sensor which will alarm immediately.

If one or more alarms are present and there has been no
keypad activity for at least 5 minutes, the Alarms menu
displays and cycles through the active alarms.

You can also navigate to the Alarms menu at any time.

Clearing Alarms

Once the alarm has been identified and the cause has
been removed (e.g. replaced faulty sensor), the alarm can
be cleared from the display.

To clear an alarm, perform the following:

1.

Navigate to the desired alarm.

2.

Press the



button.

3.

ERASE? displays.

4.

Press the



button.

5.

ALARM ERASED displays.

6.

Press the

button (MenuUp/Exit) to complete

the action and return to the previous menu.

NOTE:

If an the alarm still exists after you clear it, it re-
displays within 5 seconds.

«
...
30
31
32

Содержание JADE W7220

































Отзывы:

Нет отзывов