Honeywell HTRD400 Скачать руководство пользователя страница 76

Страница: 76 / 176

Rev 1.02

Document 900.0328

05/05

System Configuration

Figure 5-21

Camera Edit

17. Follow

Table 5-11

to modify the camera settings.

18. Repeat

step 16

and

step 17

for each camera.

19. When you are finished modifying the camera settings, click OK to return to the Rule

Configuration (Cameras). Your new settings display.

Table 5-11

Camera Edit Fields

Field Description

Name

Displays the camera name. This is a non-editable field.

Quality

Select the image quality. Options are:

Extended

Good

Better

Best

Resolution

Set the image resolution. Options are:

QVGA

. Standard resolution

VGA

. Highest resolution

Frame Rate

Set the Frame Rate (Frames Per Second) recorded from each camera. The FPS
rate depends on the image resolution setting. Options are:

QVGA

. 30 FPS maximum

VGA

. 15 FPS maximum from each camera

Note

You must configure at least one camera with a minimum 1 FPS for a rule
to be valid (so the system will record).

Содержание HTRD400

















































































































































































Результаты поиска

Содержание HTRD400

Отзывы:

Honeywell HTRD400, Справочное руководство, Страница: 76 / 176

Результаты поиска

Содержание HTRD400

Отзывы: