Honeywell HM700A1000 Скачать руководство пользователя

Страница: 1 / 28

INSTALLATION INSTRUCTIONS

33-00118-01

HM700A1000

ELECTRODE STEAM HUMIDIFIER

INTRODUCTION

The HM700 is the most advanced residential steam humidifier

available and provides steady and reliable humidification for a

home. The humidifier is designed for connection to a steam

distributor installed in a supply air duct for humidity on

demand.

IMPORTANT

Read and save these instructions. This guide should

be kept by the installer, and the Homeowner’s Guide

should be left with the equipment owner.

Included in the Box

— Steam Humidifier (HM700)

— Distribution Remote Mount Kit (HM700ADISTKIT)

— HumidiPRO Humidistat (H6062A1000)

— Steam Cylinder (one HM700ACYL2 included)

— Rubber drain hose

— Installation Instructions, Homeowner’s Guide and

Quick Start Guide

Tools Needed

— Screwdriver

— Wrench

— Pliers

— Shut-off water valve

— Water line (LDPE or Copper)

Humidifier Configuration

The HM700 is configured at the factory to operate under most

conditions without the need to change its configuration.

NOTE: Because the humidifier is factory configured for

optimal performance, Honeywell strongly

discourages changes to the jumpers or the

potentiometer; doing so will void the warranty

and could damage the humidifier. Contact

Honeywell Customer Care for further

information.

Before Installation

Ensure that available voltage and phase corresponds

with humidifier voltage and phase as indicated on

humidifier’s specification label.

Ensure that the dedicated external fuse disconnect is of

sufficient size to handle the rated amps as indicated on

the specification label. Refer to local codes.

Ensure sufficient clearances will be available as

described in the Location section on page 5.

Ensure steam lines can be routed to duct distributor as

described in Steam Lines and Condensate Return

Instructions on page 8.

Table 1. Specifications.

Part Number

Volts

Steam

Output

GPD

Amps Phase

Max Ext

Fuse

Standard

Cylinder

Net/Full

Weight

lbs. (kg)

Dimensions

in inches

(L x W x H)

HM700A1000

110/120

1.4

12.0

15 A

CYL2

15 / 20

(7.0 / 9.5)

11.5 x 6.75 x 21.5

220/240

2.8

Содержание HM700A1000





























Результаты поиска

Содержание HM700A1000

Отзывы:

Похожие инструкции для HM700A1000

Бренды по названию

Популярные бренды

Honeywell HM700A1000, Руководство по установке

Результаты поиска

Содержание HM700A1000

Отзывы:

Похожие инструкции для HM700A1000

Бренды по названию

Популярные бренды