manualshive.com logo in svg

Honeywell HF800 Series, Справочное руководство

Поделиться
Скачать
Honeywell HF800 Series Скачать руководство пользователя страница 37

37 

Restore to Default 

To return a device to its absolute Factory default parameters it is necessary to use 
the Restore Factory Defaults Tune. You will be prompted to confirm. All Environment 
parameters will be restored to Factory default values and any existing configurations 
stored on the device will be erased. The device will be reset and therefore start in run 
mode with the factory default configuration. 
Operating steps: 
1. Keep press the button “Tune” for more than 20s, then release the button, reader

will enter the mode waiting for user to confirm the default operation. the “Train”
(red/green led) flashing through 5Hz.

2. If press the button again in 10s, the reader will return to default configurations.

If reader return to default configuration success, the beeper will execute a

menu configure good tone. The Read led will indicate green.

If doesn’t press the button again beyond 10s, the reader will return to previous
work states.

Содержание HF800 Series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды