Honeywell HERMetic UTImeter Gtex Chem IIC Скачать руководство пользователя страница 31

Страница: 31 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

5.2 Selecting the temperature resolution

The temperature reading can be given with 1 or 2 digits after the dot. Select the appropriate resolution as

shown on Figure 9-4.

Figure 9-4

Switch on the equipment,

Wait until the temperature is displayed,

Press on "+" to enter the settings menu,

Press on "enter", "LED menu" is displayed,

Press on "+"; "T. unit" is displayed,

Press on "+", "Resol." is displayed,

Press on "enter",

Select the resolution by pressing on "+" one or more times, the pointer shows the resolution selected,

Press "-" two times to come back in measurement mode.

The new setting is stored in the permanent memory.

UTImeter

Battery

Init.

********

25.94

Settings

T. unit

Resol.

>0.0

> 0.00

Ver x.xx

LED menu



97%

Содержание HERMetic UTImeter Gtex Chem IIC




















































































Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы:

Honeywell HERMetic UTImeter Gtex Chem IIC, Руководство по эксплуатации и обслуживанию, Страница: 31 / 83

Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы: