Honeywell HERMetic UTImeter Gtex Chem IIC Скачать руководство пользователя страница 22

Страница: 22 / 83

50489/GTEX Chem IIC/1805

UTImeter Gtex Chem IIC

6.7. Gas tightness

All parts are assembled together with either

gaskets or O-rings, that makes the device

completely tight.

The sealing of the axle holding the tape with the

mechanical housing is ensured by a special V-

shape gasket.

6.8. Gaskets

On UTImeter Gtex Chem models, gaskets which

are in contact with the liquid are made in FFKM.

6.9. Housing and lid

These parts are made in aluminium coated with

PA11 (Rilsan®).

6.10. Others

The tape is coiled on the axle which holds also the

electronic box and the display unit.

The axle is assembled to the electronic box and

can be locked at discrete positions by means of a

stopping mechanism in the crank. Pull the crank to

free the stopping mechanism.

The storage tube is threaded to the frame.

The storage tube is equipped with a quick-

connector which fits on the HERMetic valves.

Содержание HERMetic UTImeter Gtex Chem IIC




















































































Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы:

Honeywell HERMetic UTImeter Gtex Chem IIC, Руководство по эксплуатации и обслуживанию, Страница: 22 / 83

Результаты поиска

Содержание HERMetic UTImeter Gtex Chem IIC

Отзывы: