2 | HD62(X) Indoor IR Minidome Camera
+1.800.323.4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any
means without written permission from Honeywell. The information in this publication is believed to be accurate
in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use
thereof. The information contained herein is subject to change without notice. Revisions or new editions to this
publication may be issued to incorporate such changes.
Document 800-15842V1 – Rev A – 11/2013
Mounting the Camera
1.
Place the mounting template on the ceiling or wall where you want to
install the camera, drill four holes at the marked locations, and then
insert the supplied plastic anchors into the holes.
2.
Remove the dome cover from the
dome base. Insert a coin in the notch
and then twist to pry the cover from
the base.
3.
Connect the video and power
cables.
4.
Attach the dome base to the ceiling or wall using the supplied mounting
screws.
Adjusting Angle of View, Zoom, and Focus
1.
Connect a portable service monitor to the 2-pin video out connector on
the camera control board using the supplied service monitor cable.
2.
Point the camera and adjust zoom and focus as needed.
Configuring the Camera Settings
Configure the camera on-screen display (OSD) menu settings using the OSD
controller joystick on the camera control board. See the HD62(X) operation
guide for details.
Replacing the Dome Cover
After you have finished configuring the camera settings, replace the dome
cover on the dome base. Snap the cover into place.
Video Output
(Yellow)
Power Input
12 VDC (Red)
Video Output
GND
DOWN
UP
RI
GH
T
LEFT
PRESS
=SET
Service Monitor Connector
Camera Control
Board
4
3
2
1
1. Tilt rotation: Adjusts vertical angle
2. Pan rotation: Adjusts horizontal angle.
3. Focus handle: Focus (far or near)
4. Zoom handle: Zoom (tele or wide)
Specifications
Video Standard
NTSC, PAL
Image Sensor
1/3-inch interline transfer CCD
Number of Pixels (H × V)
976 × 494 (NTSC)
976 × 582 (PAL)
Minimum Illumination
0 lux with IR LEDs on; 0.1 lux color @ 30 IRE, AGC max
Video Output
1.0
V
p-p, 75 ohms
Sync System
Internal
S/N Ratio
50 dB or more (AGC off)
Horizontal Resolution
630 TVL
Auto Gain Control
0–20 dB
Automatic Electronic Shutter
1/60–1/120,000 s (NTSC)
1/50–1/120,000 s (PAL)
White Balance
ATW/Push/Manual
D-WDR
Off/Low/Middle/High
BLC
Off/Low/Middle/High
Day/Night
IRed/Auto/Day/Night
Motion Detection
4 programmable zones
Privacy Masking
8 programmable zones
IR LEDs
850 nm, 20 LEDs
IR Illumination Distance
Up to 65 ft (20 m), depending on scene reflectance
Lens Type
2.8–12 mm varifocal manual iris, DC drive, F1.4
Angle of View
Horizontal: 90°– 28°
Vertical: 65°–21.2°
Diagonal: 114°–36°
Input Voltage
12 V DC (±10%)
Power Consumption
3.6 W (max)/300 mA
Temperature
Operating: 14°F to 122°F (–10°C to 50°C), RH 30%–80%
Storage: –4°F to 140°F (–20°C to 60°C), RH 20%–90%
Dimensions (W × H)
5.1” × 3.9” (130.6 mm × 100.0 mm)
Weight
0.76 lb (0.34 kg)
3.9
″
(100 mm)
4.2
″
(107 mm)
0.18
″
(4.5 mm)
5.1
″
(130.6 mm)
3.
9
″
(1
0
0
m
m
)
