www.honeywellvideo.com
+1.800.323.4576 (North America only)
https://honeywellsystems.com/ss/techsupp/index.html
Document 800-13600V1 – Rev A – 05/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by
any means without written permission from Honeywell. The information in this publication is believed to
be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences
resulting from the use thereof. The information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to incorporate such changes.
3.
With a Phillips screwdriver, push and turn the three (3) spring-loaded screws
ninety degrees (90°) to rotate the wing tabs outward.
4.
Adjust the gimbal position, field of view, and focus as desired
(see
Setting Up the Camera
).
Pendant Mount
1.
Attach the pendant mount to the mounting surface using appropriate hardware
(not supplied).
2.
Attach the base skirt to the pendant mount.
3.
Attach the main camera assembly to the base skirt.
4.
Adjust the gimbal position, field of view, and focus as desired
(see
Setting Up the Camera
).
Setting Up the Camera
Adjusting the Gimbal
Rotate and tilt the gimbal as desired.
Adjusting the Field of View
1.
Loosen the zoom screw.
2.
Move the screw right to zoom in
(tele) or left to zoom out (wide).
3.
Tighten the zoom screw to lock
it in place.
Adjusting the Focus
1.
Loosen the focus screw.
2.
Move the screw right to focus near or left to focus far.
3.
Tighten the focus screw to lock it in place.
Configuring the Camera Settings
Connect to a spot monitor.
Configure the camera settings using the OSD. Refer to the
3 Inch High Resolution Indoor
Minidome Camera Configuration Guide
for detailed configuration instructions. Use the
controller joystick to navigate through the OSD menu structure.
Replacing the Dome Cover
Re-attach the dome cover to the camera base by lining up the yellow stickers and snapping
the dome cover into place.
Regulatory Statements
FCC Compliance
Information to the User:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Note
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Canadian Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the essential
protection requirements of the EMC directive 2004/108/EC, conforming to the requirements of
standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60065 for electrical equipment
safety.
WEEE (Waste Electrical and Electronic Equipment)
2
Rotation 360°
Tilt 70°
Pan 355°
Pan 360°
Zoom
Focus
OSD Joystick
2nd Video Out
Spot Monitor
1. EXPOSURE
LENS
BACKLIGHT
AGC
SENSE-UP
3D DNR
EXIT JUMP
2. COLOR
WB MODE
RED GAIN
BLUE GAIN
COLOR MODE
EXIT JUMP
3. DAY&NIGHT
D&N MODE
NIGHT C.
NIGHT A.
EXIT JUMP
4. FUNCTION
MIRROR
SHARPNESS
GAMMA
SLC
NIGHT-UP
EXIT JUMP
5. MOTION
AREA SET
SENSITIV.
SHOW INDI.
EXTER OUT
EXIT JUMP
6. PRIVACY
MASK 1
MASK 2
MASK 3
MASK 4
MASK 5
MASK 6
MASK 7
MASK 8
EXIT JUMP
7. SETUP
TITLE
DPC SET
MONITOR
LANGUAGE
OSD COLOR
COMMUNICA.
FACTORY SET
EXIT JUMP
8. EXIT
SAVE&EXIT
EXIT
Correct disposal of this product (applicable in the European Union and other
European countries with separate collection systems)
This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.
3
