background image

ELECTRICAL RATING (A at 50 or 60 Hz):

H46D

120 Vac

240 Vac

Full Load

4.4

2.2

Locked Rotor

26.4

13.2

Resistive

12.0

6.0

Pilot Duty

50 VA at 24 

a

H46F model available with 8 or 12 A resistive rating

at 120 Vat.

SET POINT ADJUSTMENT: Control knob on face of

controller.

SWITCHING: Enclosed, dust-proof, snap-acting, spst

switch.

SENSING ELEMENT: Nylon ribbon.
DIFFERENTIAL Nonadjustable, 5   1 percent RH.

MAXIMUM AM BlENT TEMPERATURE: 125° F [52° C].
MOUNTING MEANS:

 

 on vertical switch box with

adapter plate.

H46E,F—Mounts directly on wall with two screws

through keyhole slots in back of case.

COVER DIMENSIONS: See Figs. 1 and 2.
COVER FINISH: Silver bronze.
COVER MATERIAL Molded plastic.
UNDERWRITERS LABORATORIES, INC., LISTED: File

No. E4436; Guide No. XAPX.

CANADIAN STANDARDS ASSOCIATION LISTED: File

No. 1620; Guide No. 400E0.

 

 

16

[37.

32

[118.3]

[82.6]

 [13.5]

 [6.4

3194A

FIG. 

 DIMENSIONS IN in. [mm II

BRACKETS] FOR 

[12.7]

 

[34.9]

I

I

3193A

 2-INSTALLATION DIMENSIONS IN in.  [mm IN

BRACKETS] FOR 

WHEN INSTALLING 

THIS PRODUCT. . .

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazardous

condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for
your application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

Disconnect power supply before beginning in-
stallation to prevent electrical shock or equipment

damage.

MOUNTING

Follow manufacturer’s instructions, if available. Other-

wise proceed as follows. The H46C,D,E,F mount on a
wall at a location that will best sense the relative
humidity of the room. The H46C and D models must be
mounted with the adapter plate on a vertical switch
box. H46E and F models mount with two screws in

keyhole slots in back of case.

WIRING

All wiring must comply with local codes and

ordinances.

FOR MILDEW CONTROL

AND DEHUMIDIFICATION

Vacation homes that are unoccupied during the hot,

humid Florida summer are an invitation to mildew. The

3

60-2097—2

Содержание H46C-F







Отзывы:

Похожие инструкции для H46C-F