Honeywell Genesis 7580G Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 202

background image

6 - 1

6

Symbologies

This programming section contains the following menu selections. Refer to

for settings and defaults.

All Symbologies

If you want to decode all the symbologies allowable for your scanner, scan the

All Symbologies On

code. If on the other hand,

you want to decode only a particular symbology, scan

All Symbologies Off

followed by the On symbol for that particular sym-

bology.

Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled. 2D Postal Codes must be enabled separately.

Message Length Description

You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code
doesn’t match the valid reading length, the scanner will issue an error tone. You may wish to set the same value for minimum
and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread.

EXAMPLE:

Decode only those bar codes with a count of 9-20 characters.
Min. length = 09Max. length = 20

•

All Symbologies

•

Interleaved 2 of 5

•

•

•

China Post (Hong Kong 2 of 5)

•

•

Chinese Sensible (Han Xin) Code

•

•

•

•

•

•

•

•

•

Postal Codes - 2D

•

•

Postal Codes - Linear

•

Code 32 Pharmaceutical (PARAF)

•

•

•

GS1 DataBar Omnidirectional

•

•

•

•

Straight 2 of 5 IATA (two-bar start/stop)

•

•

Straight 2 of 5 Industrial (three-bar start/stop)

•

•

TCIF Linked Code 39 (TLC39)

•

GS1 Composite Codes

•

•

GS1 DataBar Expanded

•

•

GS1 DataBar Limited

•

•

GS1 DataBar Omnidirectional

•

UPC-A/EAN-13 with Extended Coupon Code

•

•

•

•

All Symbologies On

All Symbologies Off

«
...
79
80
81
82
83
...
»

Содержание Genesis 7580G











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Genesis 7580G

Бренд: Rakuten Страницы: 38

Бренд: Comm-co Страницы: 32

Бренд: Reinecker Страницы: 34

iCLASS SE RKCLB40E

Бренд: HID Страницы: 31

Бренд: Rosslare Страницы: 2

Бренд: Bell System Страницы: 21

F5 Series Easy Connect

Бренд: Motion Страницы: 28

Бренд: RocketFish Страницы: 2

Бренд: Kruger&Matz Страницы: 32

Бренд: Manhattan Страницы: 2

Бренд: 3nStar Страницы: 20

Бренд: Gembird Страницы: 13

Бренд: Jadak Страницы: 90

Бренд: Obreey Страницы: 46

Бренд: Datalogic Страницы: 7

Бренд: Axicon Страницы: 24

Бренд: VANCH Страницы: 17

Бренд: Amazon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды