manualshive.com logo in svg

Honeywell ECS Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Honeywell ECS Series Скачать руководство пользователя страница 71

ECS Series Emergency Communication System Installation Manual                                                           151455

4-46

Instead, separate the wiring as follows:

DO NOT pull wires from different groups through the same conduit.

Twisted, shielded wire is recommended for all audio circuits to provide the maximum protection against 
EMI and AFI emission and susceptibility.

If using shielded cable, attach the shield to earth ground on the control panel.

For the same reasons, wiring within the cabinet should be routed around the perimeter of the cabinet. 
It should not cross the printed circuit board where it could induce noise into the sensitive 
microelectronics or pick up unwanted RF noise from the high speed circuits.

Note: Ground Fault Impedance to any Terminal is 0 

Ω.

High frequency noise, such as that produced by the inductive reactance of a speaker or bell, can also 
be reduced by running the wire through ferrite beads or by wrapping it around a ferrite toroid core. See 
Figure 4-60.

Figure 4-60  Wire Routing Example for ECS-DUAL50W

1/4” spacing must be maintained

Input/Output Type:

Wiring

between each of these circuit types;

Non Power-Limited:

AC power, Standby batteries

as well as between power limited

Power-Limited:

SBUS, VBUS

and non power-limited circuits.

Audio:

Speaker

Содержание ECS Series



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды