Honeywell DT92E Скачать руководство пользователя страница 1

Страница: 1 / 20

95-3 Wireless room thermostats, wired valves, wireless

TPI boiler control

95-1 Wireless room thermostats, wired valves, wired TPI

boiler control

95-2 Wireless room thermostats, wired valves, OpenTherm 2

wire boiler control

Y9520Z Sundial RF² Pack 5

INSTALLATION INSTRUCTIONS

50047644-006 A

Application

This pack provides a wireless control solution for adding 2 wireless room

thermostats to heating systems, in order to split the heating system

into 2 separate zones and ensure compliance with the latest Building

Regulations.

Pack Contents & Product Descriptions

1 x ST9520C1005

Wireless enabled 7 day programmer with 2

output control relays for switching boilers, pumps

and zone valves in heating systems. It requires

permanent mains 230Vac power.

2 x DTS92E1020

Wireless digital room thermostat with energy

saving ECO function. It operates on 2 x AA alkaline

batteries, giving a battery life of at least 2 years

under typical operating conditions.

2 x table stand for DT92E

(optional)

Other Honeywell products, not supplied in this pack, may be required

for a complete installation, depending on the application. For example

BDR91T1004 relay box. See Schematic System Layouts (below) or refer

to www.honeywelluk.com for full details.

Schematic System Layouts

System Operation

DT92E and ST9520C use 2-way communication on an 868MHz radio

frequency (RF) band to control the heating system.
ST9520C operates as the control hub of the system and the DT92E

thermostats are free to be positioned in suitable locations in the 2

separate heating zones.
This functionality is ideal for upgrading existing systems without a room

thermostat to ensure compliance with Building Regulations. It is also ideal

for refurbished systems, where running mains cable from the programmer

to the thermostats and back to the boiler is difficult or impractical.
There are various options for how to connect to the boiler. The simplest

is a direct 230Vac connection. If the boiler supports OpenTherm

communications technology, it is possible to control it using a 2-wire

connection from the ST9520C OpenTherm terminals. If the boiler is

located remotely, it is possible to send the switching signal from the

ST9520C to a remote located BDR91T relay box.

2-way wireless

communication

Honeywell

Sundial RF² is a registered

trademark of Honeywell Inc.

OpenTherm®

communication

V4043H

ZONE 1

ZONE 2

V4043H

Radiator(s)

DT92E

ST9520C

Junction

Box

Junction

Box

Junction

Box

Hot Water

V4043H

ZONE 1

ZONE 2

V4043H

Radiator(s)

DT92E

ST9520C

Boiler

Hot Water

BDR91T

V4043H

ZONE 1

ZONE 2

V4043H

Radiator(s)

DT92E

ST9520C

Boiler

Hot Water

OpenTherm®

2-wire connection

This document is to be left with the user

Содержание DT92E





















Результаты поиска

Содержание DT92E

Отзывы:

Похожие инструкции для DT92E

Бренды по названию

Популярные бренды

Honeywell DT92E, Руководство по установке

Результаты поиска

Содержание DT92E

Отзывы:

Похожие инструкции для DT92E

Бренды по названию

Популярные бренды