manualshive.com logo in svg

Honeywell DirectLine DL424, Руководство пользователя, Страница: 19 / 38

Поделиться
Скачать
Honeywell DirectLine DL424 Скачать руководство пользователя страница 19

  

Configuration

 

3.  Configuration 

3.1 Overview 

Configuration Parameters 

Set Up consists of configuring the following functions: 

 

Atmospheric Pressure 
Compensation: 

  

The solubility of oxygen in water and 
DL5000 dissolved oxygen probe signal 
directly respond to barometric pressure 
and hence pressure compensation is 
not required during use.  For best 
accuracy, the DL424/425 modules 
need to know barometric pressure at 
the time of probe calibration.  If 
barometric pressure is known, this 
value can be readily entered into the 
instrument at this time.  This value will 
be automatically accessed during air 
calibration. 

A major contributor to atmospheric 
pressure is altitude above or below sea 
level.  In the absence of a specific 
knowledge of barometric pressure 
value, use the nominal barometric 
pressure value from 

Table 3-1

. 

The factory default barometric pressure 
value is 760 millimeters of mercury 
(mmHg).  Any value can be entered in 
one step increments from 500 to 800 
mm Hg. 

Table 3-1   Dependence of Barometric 

Pressure on Altitude 

Alt, ft

P, mmHg

Alt, ft

P, mmHg

Sea Level

760

3000

681

200

755

3200

676

400

749

3400

671

600

744

3600

666

800

738

3800

661

1000

733

4000

656

1200

728

4200

652

1400

722

4400

647

1600

717

4600

642

1800

712

4800

637

2000

707

5000

632

2200

701

5200

628

2400

696

5400

623

2600

691

5600

618

2800

686

5800

614

 

 

Salinity:

 

The solubility of oxygen in salt or brackish waters, containing much 

more than 1 part per thousand (ppt) total dissolved solids, is dependent on salt 
concentration.  The DL424 instrument accepts the total dissolved salt 
concentration in ppt and performs necessary calculations to obtain the correct 
dissolved oxygen concentration over salt concentration and sample temperature. 

The DL 424 factory default value is 0 ppt but valid readings can range from 0 - 40 
ppt and can be entered by the user in 0.1ppt increments. 

The DL425 is intended for high purity water applications; salinity compensation is 
not employed here. 

9/11 DirectLine® 

DL424/425 Sensor Module User Manual 

13 

Содержание DirectLine DL424







































Отзывы:

Нет отзывов