Honeywell ControlEdge 900 platform Скачать руководство пользователя страница 122

Страница: 122 / 230

AWG
No.

Diameter
inches

Type
K

Type
J

Type T

Type
E

Type S
Pt/
PT110

Type R
Pt/
PT113

Type
W5/
W26

Type
W/
W26

0.0100

5.984

3.551

3.043

7.169

1.85

1.91

2.38

2.03

Table values are shown as a reference only; actual values may vary. Consult
manufacturer specifications.

Isolation

This module has eight inputs, which are isolated except for RTD
current sources.

RTD Inputs

RTD inputs share current sources (two RTD inputs per source), as
shown below:

Figure 5-30: RTD Inputs

For example, the current source for the RTD input at channel one
(terminals 1 and 2) is terminal 3 (IRTD 1 & 2). This same current
source (IRTD 1 & 2) is also used for an RTD input at channel two
(terminals 4 and 5).

Figure on

RTD Inputs

and Figure on

Universal Analog Input Module

(UAI) Wiring

shows the examples of RTD input wiring (2-wire and 3-

wire RTDs). Four-wire RTD inputs are not available.

122

Содержание ControlEdge 900 platform







































































































































































































































Результаты поиска

Содержание ControlEdge 900 platform

Отзывы:

Honeywell ControlEdge 900 platform, Руководство по планированию и установке оборудования, Страница: 122 / 230

Результаты поиска

Содержание ControlEdge 900 platform

Отзывы: