manualshive.com logo in svg

Honeywell Class 500, Руководство по установке, Страница: 2 / 16

Поделиться
Скачать
Honeywell Class 500 Скачать руководство пользователя страница 2

CLASS 500 ADVANCED KWH/DEMAND METER

62-0304—05

2

SPECIFICATIONS

Input Voltage Configuration:

3-wire (Delta) or 4-wire (WYE)

Mains Voltage Input:

Up to 600 VAC RMS available

Input Power:

6 VA maximum rating

Current Sensor Rating:

Up to 3200 Amp RMS AC available

Power Factor:

.5 leading or lagging

Line Frequency:

50-60 Hz

Metering Accuracy:

Certified to ANSI C12.16

Voltage Operating Range:

+/-10% of rated load

Temperature Range (Class 500):

NEMA 4 (Outdoor) Housing: -20 ºC to +70 ºC

NEMA 12 (Indoor) Housing: -20 ºC to +50 ºC

Relative Humidity Range:

0-95% non-condensing

Altitude:

2000 meters maximum

Voltage Overload:

+25% continuously; +100% for 20 cycles

Current Sensor Overload:

100% for 1 minute without damaging meter

Pollution Degree:

Degree 2 In accordance with IEC 664

Installation (Overvoltage) Category:

Category III

Measurement Category:

Category III

Outdoor Housing Rating (Model numbers with an R at the 

end):

NEMA 4

Indoor Housing Rating (Model numbers without an R at 

the end):

NEMA 12

Display Readout:

KWh accumulated

Standard Ranges:

(3 or 4 Wire) 120/208-240V: 100,200,400,800,1600, 3200 

Amp

(3 or 4 Wire) 277/480V: 100,200,400,800,1600, 3200 Amp

(4 Wire) 346/600 V: 100,200,400,800,1600, 3200 Amp

RS485 Serial Communication Interface:

Cable Specifications:

 UL listed/rated telephone cord, 

4 conductor, 300VAC, stranded conductors, 22-26 AWG.

Input/Output Voltage:

 Ground is/-5.4 VDC

Cable Connector:

 RJ-11 connector

Ckt Input Isolation:

 5.3 KVAC

Max Cable Distance:

 4000 feet

Max Network Nodes:

 Maximum cabling nodes 52 

including master node

Baud Rate:

 9600

Communications Options:

RS232/RS485 (Standard) (Requires E-Mon Energy.)

Telephone Modem (Requires E-Mon Energy.)

Ethernet (Requires E-Mon Energy.)

Modbus RTU or TCP/IP (Requires third-party EMS/BMS.)

BACnet IP or MS/TP (Requires third-party EMS/BMS.)

LONworks TP (Twisted Pair) (Requires third-party EMS/

BMS.)

Recommended In-Line Fuse:

Manufacturer:

 Littelfuse

Mfg Part No.:

 KLDR.100

Rating:

100 mA, time delay. 600 VAC cartridge fuse

Battery Cell:

Description:

 Non-rechargeable cell used for memory 

retention.

Manufacturer:

 Eagle-picher

Mfg Part No.:

 LTC-3PN

Working Voltage:

 3.5 Vdc

Current Capacity:

 350 mAHr

Electrolyte:

 Lithium thionyl nitrate

Содержание Class 500

















Отзывы:

Нет отзывов