Honeywell CGW-MB Скачать руководство пользователя страница 168

Страница: 168 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

167

Gent Panels

Connecting to the Panels

C.8.3 Vigilon Series Panels

For a fixed CLSS Gateway mainboard, we recommend using a UART/TTL connection. If it
is not available, use a RS-232 connection.

To Use a UART/TTL Connection

1. On the CLSS Gateway mainboard Side

Connect the male UART/TTL cable to the Rx (Red), Gnd (Silver), and Tx (White) UART/TTL
terminals of the CLSS Gateway mainboard.
The UART/TTL port is labeled as 5 in

Figure C.2

2. On the Panel Side

1. Within the panel, find the backplane PCB board (see

Figure C.21)

2. Connect the 3.5mm phono socket to the P11 connector on the panel’s PCB.

Figure C.21: Vigilon Panels: UART/TTL Connection

3. Power Connection

On the CLSS Gateway mainboard Side
Connect the power cable to a 24V DC external power source.

To Use an RS-232 Port via an I/O Card

Using an add-on I/O card (VIG-IOC-DOM), certain Vigilon panel variants can
communicate with the CGW-MB.
•

The I/O card has a rotary switch, which should point to 5.

•

The baud rate of the I/O card should be 19200.

NOTE:

The external power supply must be dedicated and not shared with any other

devices.

NOTE:

The panel’s power supply to the CLSS Gateway mainboard must be 24V DC

power.

Содержание CGW-MB




























































































































































































Результаты поиска

Содержание CGW-MB

Отзывы:

Honeywell CGW-MB, Инструкция по установке и эксплуатации, Страница: 168 / 187

Результаты поиска

Содержание CGW-MB

Отзывы: