background image

50118845-001 Rev B 10/15

© 2015 Honeywell International Inc. All Rights Reserved.

Page 9

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document 
without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.  The infor-
mation in this publication does not represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting 
from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hard-
ware to achieve intended results.

This document contains proprietary information that is protected by copyright.  All rights are reserved.  No part of this document may be 
photocopied, reproduced, or translated into another language without the prior written consent of HII.



2015

 

Honeywell International Inc.

  

All rights reserved.

Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the 
property of their respective owners.

Web Address: 

www.honeywellaidc.com

Patents

For patent information, please refer to 

www.hsmpats.com

.

Technical Assistance

Contact information for technical support, product service, and repair can be found at 

www.honeywellaidc.com

.

Limited Warranty

Refer to 

www.honeywellaidc.com/warranty_information 

for your product’s warranty information.

User Documentation

To download user documentation go to 

www.honeywellaidc.com

.

Содержание 9000301PWRSPLY











Отзывы: