On Vista 32/40/50/50P/100, and up
You must assign a user to the button in order for it to operate.
To assign a user number to the Arm/Disarm button:
1. Enter [4-digit User Code] + [8] + [User No.] + [4-digit new
User Code].
2. Answer Yes or No to the “Open/Close Report ?” question.
3. Answer Yes to the “RF Button ?” question.
4. Enter the zone number assigned to the Arm/Disarm
button.
5. Keypad shows the summary of user information on its
display.
6. Test Arm/Disarm button to make sure it operates correctly.
On Vista-20P/15P/10P and variants
You must assign a user to the button in order for it to operate,
and must enter a sequence of keystrokes as described
below.
NOTE:
There is a two-second timeout for keystroke
commands on Vista P series panels, therefore you must
enter the keystrokes as quickly as possible.
1. Enter [4-digit Master Code] + [8] + [User Number] + [# 4]
+ [two digit zone number] assigned to the fob.
2. Test Arm/Disarm and other functions to confirm proper
operation.
REPLACING THE BATTERY
The LED will not flash during transmission if the battery is
low. Replace the battery as follows.
1. Remove the screw from the case back, then remove the
case back.
2. Insert the blade of a small screwdriver under the battery
as shown below.
3. Twist the screwdriver to release the battery.
4. With the Positive (+) end of a new battery facing UP,
insert the battery as shown, sliding it under the gold tab,
then pressing down to snap into place.
IMPORTANT:
Positive (+) end must face up.
Use Maxell CR2032 or Duracell DL2032 lithium battery
only.
5. Replace the case back and replace the screw to secure
the case.
!
•
••
•
Improper installation will result in
damage to the battery.
•
••
•
Do not remove the printed circuit board.
Failure of Replaceable Batteries
This wireless key has been designed to provide several
years of battery life under normal conditions. The
expected battery life is a function of the device
environment, usage and type. Ambient conditions such
as high humidity, high or low temperatures, or large
temperature fluctuations may reduce the expected
battery life.
This device will report a low battery condition to the
control panel as a trouble condition, when the batteries
need to be replaced. In addition the LED will not flash
when a button is pressed. However, if the device is
unused for a long period of time, it may fail to operate as
expected. Regular testing and maintenance will keep the
system in good operating condition for the lifetime of the
product.
IMPORTANT!
This wireless key is intended as a
convenience to the user and should not be considered as
a life safety device. If life safety is important, please
select a supervised wireless key (e.g. type 5802MN).
WARRANTY INFORMATION
For the latest warranty information, please go to:
http://www.security.honeywell.com/hsc/resources/wa/index.html
5834-004-V0
GOLD
TAB
BATTERY
TO REMOVE, SLIDE
SCREWDRIVER BLADE
UNDER BATTERY HERE
Removing the Battery
5834-005-V0
INSTALL WITH POSITIVE (+)
SIDE UP. SLIP BATTERY
UNDER GOLD TAB THEN
PRESS DOWN
IMPORTANT
POSITIVE (+)
SIDE MUST
FACE UP
BA
TT
ER
Y
INSTALL UNDER GOLD TAB
BA
TTER
Y
THEN PRESS DOWN
Installing the Battery
SPECIFICATIONS
Unit Dimensions:
2.25" x 1.25" x 0.5"
(57mm x 31.75mm x 12.7mm)
Battery:
3V, 210mAh, Maxell CR2032, Duracell DL2032
REFER TO THE INSTALLATION INSTRUCTIONS FOR
THE CONTROL WITH WHICH THIS DEVICE IS USED
FOR LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS:
The user shall not make any changes or modifications to the
equipment unless authorized by the installation Instructions or
User's Manual. Unauthorized changes or modifications could void
the user's authority to operate the equipment.
FCC NOTICE
This device complies with Part 15 of FCC Rules, and RSS 210 of
IC. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that
may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de
RSS 210 des industries Canada. Son fonctionnement est soumis
aux conditions suivantes: (1) Cet appareil ne doit pas causer
d'interferences nuisibles. (2) Cet appareil doit accepter toute
interference reçue y compris les interferences causant une
reception indesirable.
Ê800-05637TŠ
800-05637 7/10 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
www.honeywell.com/security
