HW-500-003
3
I56-3934-002R
Refer to the manufacturer’s published instructions for proper use of the
canned smoke agent.
C. Direct Heat Method (5193SDT only)
Using a 1000-1500 watt hair dryer, direct the heat toward either of the
thermistors. Hold the heat source about 12 inches from the detector to
avoid damage to the plastic.
D. Auto-maintenance Feature
: Test detector alarm operation from the
control panel if applicable (refer to control panel test procedure).
If a detector fails any of the above test methods, its wiring should be checked
and it should be cleaned as outlined in the
Maintenance
section. If the
detector still fails, it should be replaced.
Notify the proper authorities when the system is back in service.
Maintenance
NOTE:
Before performing maintenance on the detector, notify the proper
authorities that maintenance is being performed and the system will be tem-
porarily out of service. Disable the zone or system undergoing maintenance
to prevent any unwanted alarms.
Power must be removed from the panel
before performing maintenance of any kind.
1. Remove the detector cover by turning counterclockwise.
2. Vacuum the cover or use canned air to remove any dust or debris.
3. Remove the top half of the screen/sensing chamber by lifting straight up
(Figure 6).
4. Vacuum or use canned air to remove any dust or particles that are pres-
ent on both chamber halves.
5. Replace the top half of the screen/sensing chamber by aligning the arrow
on the screen/sensing chamber with the arrow on the housing. Press
down firmly until the screen/sensing chamber is fully seated.
6. Replace the detector cover by placing it over the screen/sensing chamber
and turning it clockwise until it snaps into place.
7. Reinstall the detector and test. (See the
Testing
section.)
8. Notify the proper authorities when the system is back in service.
FIGURE 6: REMOVING/REPLACING SCREEN/SENSING CHAMBER
REMOVABLE
DETECTOR
COVER
SCREEN/SENSING
CHAMBER
(TOP HALF)
DETECTOR
HOUSING
S0136-00
CAUTION
Smoke detectors are not to be used with detector guards unless the combina-
tion has been evaluated and found suitable for that purpose.
Do NOT Install Detectors in the Following Areas:
In or near areas where particles of combustion are normally present
s
such as kitchens; in garages (vehicle exhaust); near furnaces, hot water
heaters, or gas space heaters.
In very cold or very hot areas.
s
In wet or excessively humid areas, or next to bathrooms with showers.
s
In dusty, dirty, or insect-infested areas.
s
Near fresh air inlets or returns or excessively drafty areas. Air condition-
s
ers, heaters, fans, and fresh air intakes and returns can drive smoke
away from the detector.
Consult NFPA 72, the local Authority Having Jurisdiction (AHJ), and/or ap-
plicable codes for specific information regarding the spacing and placement
of smoke detectors.
CAUTION
Dust covers are an effective way to limit the entry of dust into the smoke de-
tector sensing chamber. However, they may not completely prevent airborne
dust particles from entering the detector. Therefore, Honeywell recommends
the removal of detectors before beginning construction or other dust produc-
ing activity. When returning the system to service, be sure to remove the dust
covers from any detectors that were left in place during construction.
Please refer to insert for the Limitations of Fire Alarm Systems
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
For the latest warranty information, please go to: www.security.honeywell.com/hsc/resources/wa