Monitor out
= ON
= OFF
V-Phase
H
Level
L
+
–
Focus lever
(top)
Zoom lever
(bottom)
Preparation
Camera Mounting
Camera Adjustment
3. Connect the Wiring
Surface Mount
Optional Camera Settings
1. Remove the Dome Cover
2. Prepare the Mounting Surface (Surface or Flush Mount)
a. Loosen the three security screws, then
remove the dome.
b.
Gently
pull the inner liner free of the
two notches in the housing.
c.
Set the dome and liner aside.
d. Loosen the three screws connecting
the skirt and the base, then remove the
base. Continue with step 2
“Prepare
the Mounting Surface”
below.
4S Electrical Junction Box (optional)
a. Secure the adapter plate to the 4S
electrical box using the appropriate
screws, not supplied.
b. Secure the camera base to the adapter
plate using the appropriate M4 screws,
supplied.
Electrical box
(not supplied)
Base
Flush Mount
•
For adapter plate installations, secure the
base with the appropriate M4 screws,
supplied.
•
When not using the adapter plate, use
screws appropriate to secure the base to the
wall or ceiling.
Skirt
Legend
A = Tilt rotation
B = Horizontal rotation*
C = Pan rotation
.
Picture Brightness
The LEVEL screw compensates for the iris level. L (low) darkens the
picture. H (high) brightens the picture.
Phase Adjustment
The V Phase Adjustment Pot adjusts the phase difference between
cameras. Switch 7 must be
ON
to activate Line lock (AC only).
DIP Switches
(Refer to your
camera model)
Default settings are
shown in
bold
.
SW High Res + TDN
High Res
Std Res
1
DC
/AES
DC
/AES
DC
/AES
2
AWB
/ATW
AWB
/ATW
AWB
/ATW
3
BLC ON/
OFF
BLC ON/
OFF
BLC ON/
OFF
4
AGC
ON
/OFF
AGC
ON
/OFF
AGC
ON
/OFF
5
TDN
Not used
FLK/
OFF
6
FLK ON/
OFF
FLK ON/
OFF
LL ON/
OFF
7
LL ON/
OFF
LL ON/
OFF
Not available
8
Not used
Not used
Not available
Mode setting
DIP switches
After
➋
mounting and
➌
adjusting the camera, attach the
dome cover:
a. Attach the inner liner to the base until
the liner clicks into place.
b. Secure the dome enclosure to the base
with the three security screws.
B
C
A
* If necessary, loosen the screw
that locks the gimbal assembly in
place, before adjusting the
camera.
Base
Base
Screws
(not supplied)
M4 screws
(supplied)
M4 screws
(supplied)
Screws
(not supplied)
M4 screws
(supplied)
Inner liner
Dome
Use the appropriate mounting
template to:
a. Mark the holes as required.
b. Insert the screw anchors
into the holes.
Base
Skirt
a. Connect the video
output connector.
b. Connect the 24 VAC/12
VDC power connector.
c.
If necessary, tuck the
wires into the space
outside the posts
(grayed area).
Flush Mount
Surface Mount
a. Secure the skirt to the electrical box
using 2 appropriate screws (not
supplied).
b. Tuck the cables in the area outside the
posts. (See
“Connect the Wiring”
.)
c.
Secure the camera base to the skirt
using the appropriate M4 screws,
supplied.
M4 screws
(supplied)
Screws
(not supplied)
Skirt
Base
a. Secure the skirt to the ceiling or wall
using the appropriate screws, not
supplied.
b. Tuck the cables in the area outside the
posts. (See
“Connect the Wiring”
.)
c.
Secure the camera base to the skirt
using the appropriate M4 screws,
supplied.
Connect the wiring. If you need to contain the
connection within the camera housing, then try the
method shown below.
a
b
24 VAC/12 VDC
power connector
Video output
connector
Caution
Do not touch or
damage the black vent!
1
2
3
Note
Surface mount preparation shown.
Adapter plate
(use is optional)
Adapter plate
