Honda WH15XT Скачать руководство пользователя страница 21

Страница: 21 / 64

OPERATION

SUCTION HOSE INSTALLATION

Use a commercially available hose and hose connector. The hose clamp

is provided with the pump.

Most hoses come with the connectors already installed. The suction

hose must be reinforced with a noncollapsible wall or braided wire

construction and cannot contain any perforations.
The suction hose should be no longer than necessary. Pump

performance is best when the pump is near the water level, and the

hoses are short.

1.Verify that the hose coupling packing is in good condition.

2.Securely tighten the hose connector to the pump suction port.

3.Install the suction hose to the hose connector.

Use a hose clamp to securely fasten the suction hose to the hose

connector in order to prevent air leakage and loss of suction.

4.Install the strainer (provided with the pump) on the other end of the

suction hose, and secure it with a hose clamp.

The strainer will help to prevent the pump from becoming clogged or

damaged by debris.

Never operate the pump without the strainer installed.

Always use the included strainer or one with an equivalent mesh size.

Operating the pump without a strainer may result in severe pump

damage.

HOSE CLAMP

STRAINER

HOSE CONNECTOR

(Commercially available)

HOSE COUPLING PACKING

HOSE COUPLER

HOSE CLAMP RING

HOSE CLAMP

SUCTION HOSE

(Commercially available)

SUCTION PORT

31YH6600.book 19 ページ２０１５年１月８日　木曜日　午前１１時５０分

Содержание WH15XT

































































Результаты поиска

Содержание WH15XT

Отзывы:

Бренды по названию

Популярные бренды

Honda WH15XT, Руководство пользователя

Результаты поиска

Содержание WH15XT

Отзывы:

Бренды по названию

Популярные бренды