Honda SSBL Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 36

background image

4

1. Safety

1.1 Warnings

For appropriate use of the blower, follow the instructions in this manual. Warning labels are attached to
places where there are potential risks or in the periphery. The warning labels in this instruction manual are
categorized depending on the degree of risk as shown in the table below.

1.1.1 Warning Description

Signal words in this instruction manual are categorized as shown below. If the warning for each signal
word is ignored, serious injury or fatal injury may result.



Meanings of signal words

DANGER

Indicates an immediately hazardous situation which, if not avoided, will
result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, could result
in mild to moderate injury or property damage.

Note

Indicates to emphasize important information or provide helpful information.



Meanings of symbols

Caution

Sign

Indicates that hazardous situation may result due to negligence of
instructions. The hazards are designed into pictorial indication inside
the symbol.

Prohibition

Sign

Indicates prohibition of dangerous action. Prohibited actions are
designed into pictorial indication inside or by the symbol.

Enforcement

Sign

Indicates enforcement of actions. Actions to be enforced are
designed into pictorial indication inside the symbol. This action is
required to avoid hazard.

«
...
2
3
4
5
6
...
»

Содержание SSBL





































Отзывы:

Нет отзывов

Похожие инструкции для SSBL

SNOW BLADE 120 CM

Бренд: Stoeryd Страницы: 8

Бренд: Makita Страницы: 28

Бренд: Makita Страницы: 20

Бренд: Poulan Pro Страницы: 44

Бренд: Tuff & Gusty Страницы: 4

Бренд: Cub Cadet Страницы: 48

Бренд: Scarab Страницы: 2

Бренд: Dustbane Страницы: 2

Бренд: Dustbane Страницы: 8

Бренд: LOFTNESS Страницы: 35

Бренд: LOFTNESS Страницы: 36

Бренд: LOFTNESS Страницы: 37

Бренд: LOFTNESS Страницы: 38

Бренд: LOFTNESS Страницы: 44

Бренд: Badger Basket Страницы: 10

Бренд: Power Craft Garden Страницы: 50

Бренд: FIORENTINI Страницы: 37

Бренд: Snapper Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды