Honda Metropolitan CHF50 Скачать руководство пользователя страница 188

Страница: 188 / 319

FINAL REDUCTION

10-6

Remove the dowel pins.
Clean any sealant from the transmission case mat-

ing surface.

Remove the thrust washers and countershaft.

Remove the final gear shaft, counter gear and side

washer.

DRIVESHAFT REMOVAL

Remove the driveshaft using the special tools.

Remove the driveshaft oil seal and bearing.

If the bearing is left on the driveshaft, remove it with

the special tool.

DOWEL PINS

COUNTERSHAFT

FINAL GEAR SHAFT

COUNTER GEAR

WASHERS

WASHER

2002 only

TOOL:
Case puller

07SMC-0010001

CASE PULLER

OIL SEAL/BEARING

DRIVESHAFT

TOOL:
Universal bearing puller

07931-4630000 or

equivalent

commercially

available in U.S.A.

DRIVESHAFT

BEARING

BEARING PULLER

Содержание Metropolitan CHF50
































































































































































































































































































































Результаты поиска

Содержание Metropolitan CHF50

Отзывы:

Honda Metropolitan CHF50, Руководство по обслуживанию, Страница: 188 / 319

Результаты поиска

Содержание Metropolitan CHF50

Отзывы: