Honda HRR216VKUA Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

Honda HRR216VKUA Скачать руководство пользователя страница 12

12

Blade Inspection

1. Turn the fuel valve OFF (

2. Disconnect the spark plug cap from the spark plug (

3. Tilt the mower to the right side, so the fuel cap side is up. This will

help to prevent fuel leakage and hard starting due to carburetor
flooding.

4. Inspect the blades for damage, cracks, and excessive rust or

corrosion.

A dull blade can be sharpened, but a blade that is excessively worn,
bent, cracked, or otherwise damaged must be replaced.

If a blade is bent, take the lawn mower to an authorised Honda
servicing dealer for inspection.

Blade Mounting Bolt Inspection

Inspect the blade bolts for any signs of damage
or looseness. If they are damaged, they must
be replaced.

If they appear loose, a torque wrench must be
used to accurately tighten the blade bolts to the
required torque. If you do not have a torque
wrench, take your lawn mower to an authorised
dealer to have the bolts replaced and/or
tightened.

Use only Honda Genuine blade bolts and
special washers, since they are specifically
designed for this purpose.

Blade Replacement

1. Turn the fuel valve OFF (

2. Disconnect the spark plug cap from the spark plug (

).

3. Tilt the mower to the right side, so the fuel cap side is up. This will

help to prevent fuel leakage and hard starting due to carburetor
flooding.

4. Remove the two blade bolts with a 14 mm (6 point) socket

wrench. Use a wooden block to prevent the blades from turning
when removing the bolts. Remove the blades.

5. Clean dirt and grass from around the blade mounting area.

6. Install the sharpened or replacement blades using the two blade

bolts and special washers as shown below.

Always install both blades as a set.

The blade bolts and washers are specially designed for this
application. When replacing bolts and washers, use only Honda
Genuine replacement parts. Always install both blades as a set.

7. Tighten the blade bolts with a torque wrench. Use a wooden

block to prevent the blades from turning when tightening the
bolts, as shown on

.

Blade bolt torque:

49 ~ 59 N·m

If you do not have a torque wrench, have an authorised Honda
servicing dealer tighten the blade bolts.



WARNING

A worn, cracked, or damaged blade can break, and pieces of
the damaged blade can become dangerous projectiles.

Thrown objects can cause serious injury.

Inspect the blades regularly, and do not operate the mower
with worn or damaged blades.

BLADE
BOLTS

BLADES

NORMAL

WORN

BENT

CRACKED

NORMAL

TRAILING EDGE

EXCESSIVELY WORN

TRAILING EDGE

Inspect washers

and bolt heads for

looseness and

damage.



WARNING

If the blade bolts are not torqued properly, the blade could
loosen and be thrown from the mower.

Blades thrown from the mower could seriously hurt or kill
someone.

Ensure the blade bolts are torqued properly.

UPPER
BLADE

LOWER
BLADE

SPECIAL
WASHER
(2)

BLADE BOLT
(2)

BLADE BOLT [2]

AND WASHER [2]

SPECIAL WASHER
DIRECTION

UPPER BLADE

LOWER BLADE

«
...
10
11
12
13
14
...
»

Содержание HRR216VKUA

























Отзывы:

Нет отзывов