15
STORAGE
Proper storage preparation is essential for keeping your lawn mower
trouble free and looking good. To help keep rust and corrosion from
impairing your lawn mower’s function and appearance, and to make
the engine easier to start after storage, follow the instructions
described in this section to:
• Drain or treat the fuel
• Change the oil and coat the engine cylinder
• Clean the mower, engine, and grass bag
• Choose a storage location
Fuel
See “AVOIDING FUEL-RELATED PROBLEMS” on
for a list of
recommended procedures to avoid fuel related problems.
The
LIMITED WARRANTY
) does not cover fuel system
damage or engine performance problems resulting from neglected
storage preparation.
Oil
Change the engine oil (see
Add oil in the engine cylinder to prevent rust.
1. Remove the spark plug (
).
2. Pour 5 cc of clean engine oil into
the cylinder to keep it from
rusting.
3. Pull the starter rope several times
to distribute the oil in the cylinder.
4. Reinstall the spark plug.
5. Pull the starter rope slowly until
resistance is felt, and then return
the starter grip gently. This will
close the valves so moisture
cannot enter the engine cylinder.
Cleaning
Mower Deck
Allow the engine to cool before cleaning or washing.
Before cleaning or washing the underside of the mower deck, stop the
engine and turn the fuel valve to the OFF position. Rest the mower on
its right side, so the fuel cap side is up. This will help to prevent fuel
leakage and hard starting due to carburetor flooding. Wear heavy
gloves to protect your hands from the blades.
Remove any grass clippings from the underside of the mower deck,
paying attention to the areas surrounding the Clip Director shutter
lever and housing.
Be careful to avoid getting water into controls and cables, or
anywhere near the engine air cleaner or muffler opening.
Engine
Allow the engine to cool before washing.
Wash the engine by hand, and be careful to prevent water from
entering the air cleaner and exhaust opening.
NOTICE
Using a garden hose or pressure washing equipment can force water
into the air filter. Water in the air cleaner will soak the paper element
and can enter the carburetor or engine cylinder, causing damage.
Water contacting a hot engine can cause damage. If the engine has
been running, allow it to cool before washing.
Grass Bag
Remove the bag from the mower, and wash it with a garden hose or
pressure washer. Allow the bag to dry completely before storage.
Drying
After washing the lawn mower, wipe dry all accessible surfaces.
Place the mower with its wheels on a level surface. Start the engine
outdoors and let it run until it reaches normal operating temperature to
evaporate any water remaining on the engine.
Stop the engine and allow it to cool.
After the lawn mower is clean and dry, touch up any damaged paint,
and coat other areas that may rust with a light film of oil.
Storage Location
If your mower will be stored with petrol in the fuel tank and carburetor,
it is important to reduce the hazard of petrol vapor ignition. Store the
mower in a well-ventilated room away from naked flames such as may
be found in hot water heaters, furnaces, or clothes dryers. Also avoid
any area with a spark-producing electric motor, or where power tools
are operated.
Store fuel in a cool place in a container specifically designed for the
purpose. In general, plastics containers are unsuitable.
Make sure the fuel valve is in the OFF position to reduce the
possibility of fuel leakage.
Place the mower with its wheels on a level surface. Tilting can cause
fuel or oil leakage.
With the engine and exhaust system cool, cover the mower to keep
out dust. A hot engine and exhaust system can ignite or melt some
materials. Do not use sheet plastic as a dust cover. A nonporous
cover will trap moisture around the mower, promoting rust and
corrosion.
Handlebar
Remove the grass bag if installed. You can place it on top of the
engine with the bag opening to the front.
1. Turn the handlebar adjust knobs 90 degrees to release the
locating pins
.
2. Fold the handlebar forward
; do not pinch or kink the cables.
SPARK
PLUG
HOLE
OIL
