Honda HRM300 Скачать руководство пользователя страница 109

Страница: 109 / 324

6-4

dummyhead

TROUBLESHOOTING

BEFORE TROUBLESHOOTING

• Use a known-good battery for troubleshooting.

• Check that the connectors are connected securely.

• Read the circuit tester's operation instructions carefully, and observe the instructions during inspection.

DOCKING SYSTEM TROUBLESHOOTING

Can dock

The error message is displayed (page 3-15).

Displayed

Check the error message and perform the
troubleshooting for fault/warning message
(page 6-8, 6-9, 6-10).

HRM300/500 can dock to the station.

Not displayed

Check the charge current on the display with
docking to the station.
(Normal charging current is 1A or more.)

Abnormal

Battery trouble.
Replace the battery (page 10-7).

Check the transformer (page 11-3).

Abnormal

Repair the power supply.
(Contact an electric power
company if necessary.)

Normal

Check the power supply.

Normal

Abnormal

Transformer trouble.
Replace the transformer.

Main ECU trouble.
Replace the main ECU (page 10-7).

Normal

Remove the foreign substance of
the wheel(s).

Abnormal

Check the setting of HRM300/500 (page 3-53).

Normal

Set the setting again (page 3-9).

Abnormal

Check the boundary wire installation (page 3-12).

Normal

Check if foreign material blocks the wheel(s).

Cannot dock

Install the boundary wire correctly
(page 3-12).

Abnormal

Check the charge plug and socket for damage,
bent and rust.

Normal

Charge plug and/or socket
trouble.
Replace or repair the charge plug
and/or socket (page 10-6, 11-2).

Abnormal

Normal

Between the main ECU 2P connector

and charge socket terminals (

and

) of sub wire harness trouble.

Replace or repair the sub wire harness.

Содержание HRM300





































































































































































































































































































































Результаты поиска

Содержание HRM300

Отзывы:

Похожие инструкции для HRM300

Бренды по названию

Популярные бренды

Honda HRM300, Руководство пользователя

Результаты поиска

Содержание HRM300

Отзывы:

Похожие инструкции для HRM300

Бренды по названию

Популярные бренды