13
The upper blade or an optional accessory spacer plate must be
installed along with the lower blade. Never simply remove the
upper blade.
Oil Change
Change the oil after the first month or 5 hours of use. Thereafter,
change the oil every 6 months or 50 hours of use. Change the oil
more frequently when used under heavy load or high outdoor
temperatures. See “Engine Oil Recommendations” on this page for
recommended oil properties.
Drain the used oil while the engine is warm. Warm oil drains quickly
and completely.
To reduce the chance of scratching the side of the mower deck or
wheels when tipping, place a piece of cardboard or drop cloth on the
ground. The use of a commercially available siphon pump will save
time and make the oil change easier.
1. Turn the fuel valve OFF (page 3). This will reduce the possibility of
fuel leakage
2. Wipe the oil filler area clean, and then remove the oil filler
cap/dipstick.
3. Place a suitable container
next to the mower to catch
the used oil, and then tilt the
mower on its right side.
The used oil will drain
through the filler neck. Allow
the oil to drain completely.
After draining, take the oil to
your local recycling centre or
service station. Do not throw
it in the trash, pour it on the
ground, or pour it down a
drain.
4. Fill with the recommended oil. Do not overfill. Allow a couple of
minutes for the oil to settle in the engine, and then measure the oil
level (page 5).
Refill amount:
0.35 ~ 0.40 litres
NOTICE
Using non detergent oil can shorten the engine’s service life, and
using 2-stroke oil can damage the engine.
Engine Oil Recommendations
Oil is a major factor affecting performance and service life. Always
change the oil in accordance with the
Maintenance Schedule
Recommended oil for general use:
SAE 10W-30
Other viscosities shown in the chart may be used when the average
temperature in your area is within the recommended range.
The SAE oil viscosity and service category are in the API label on the
oil container. Honda recommends API service category SJ or later oil.
Air Filter
Clean the air filter after the first 25 hours of use. Thereafter, clean the
filter every 6 months or 50 hours of use. Clean the filter more often
when used in dusty areas. Replace the filter every 2 years or 150
hours of use.
A properly maintained air filter will help prevent dirt from entering your
engine. Dirt entering the carburetor can be drawn into small passages
in the carburetor and cause premature engine wear. These small
passages can become blocked, causing starting or running problems.
NOTICE
Operating the engine without an air filter, with a damaged air filter, or
with an improperly installed air filter cover will allow dirt to enter the
engine, causing rapid engine wear. This type of damage is not
covered by the LIMITED WARRANTY (page 23).
We recommend the use of a Honda Genuine air filter to ensure it
seals and performs as designed. Using a non-Honda air filter can
result in dirt bypassing the filter, causing damage to the engine or fuel
system.
1. Press down on the cover tabs and remove the cover.
2. Remove the foam element from the air cleaner cover.
3. Remove the screen grid and paper element.
4. Check both elements to be sure they are in good condition, and
replace them if they are damaged.
WARNING
If the blade bolts are not torqued properly, the blades
could loosen and be thrown from the mower and seriously
hurt or kill someone.
Ensure the blade bolts are torqued properly.
WOODEN BLOCK
TORQUE
WRENCH
TORQUE:
49 ~ 59 N•m
-20
20 30 40°C
-10 0 10
40 60
100°F
80
0
20
5W-30 • 10W-30
AIR DUCT
FOAM ELEMENT
PAPER ELEMENT
SCREEN
GRID
LATCH TABS
LOWER
TABS
AIR CLEANER
COVER
AIR CLEANER BODY
