Honda EM5000SX Скачать руководство пользователя страница 86

Страница: 86 / 124

TAKING CARE OF UNEXPECTED PROBLEMS

ENGINE WILL NOT START

Possible Cause

Correction

Fuel valve lever OFF.

Turn lever ON (see page 44).

Engine switch OFF.

Turn engine switch to ON
(see page 46).

Out of fuel.

Refuel (see page 19).

Bad fuel; generator stored without
treating or draining gasoline, or
refueled with bad gasoline.

Drain fuel tank and carburetor
(see page 79).
Refuel with fresh gasoline
(see page 19).

Low oil level caused Oil Alert to stop
engine.

Add oil (see page 40).
Turn engine switch to OFF and then
restart the engine.

Spark plug faulty, fouled, or
improperly gapped.

Gap or replace spark plug
(see page 68).

Spark plug wet with fuel
(flooded engine).

Dry and reinstall spark plug.

Fuel strainer restricted, carburetor
malfunction, ignition malfunction,
valves stuck, etc.

Take the generator to an authorized
Honda Power Equipment dealer, or
refer to the shop manual.

CO-MINDER (CO Shut-off System) is
detecting high carbon monoxide (CO)
levels around the generator.

Review the location of the generator,
such as by placing it in a well-ventilated
outdoor location (see page 26).
When the engine is stopped
automatically by CO-MINDER, press the
CO-MINDER reset button to restart the
engine (see page 49).

31Z236200.book 84 ページ２０２０年２月２０日　木曜日　午後１時８分

Содержание EM5000SX





























































































































Результаты поиска

Содержание EM5000SX

Отзывы:

Бренды по названию

Популярные бренды

Honda EM5000SX, Руководство пользователя

Результаты поиска

Содержание EM5000SX

Отзывы:

Бренды по названию

Популярные бренды