manualshive.com logo in svg

Honda EM5000SX, Руководство пользователя

Поделиться
Скачать
Honda EM5000SX Скачать руководство пользователя страница 51

OPERATION

49

STARTING AND STOPPING THE ENGINE with 

Bluetooth

® ENABLED 

SMARTPHONE

The engine can be started/stopped via a 

Bluetooth

® enabled smartphone using 

a 

Bluetooth

® application.

Refer to the 

Bluetooth

® application to check the connection, operation, and for 

help pairing a smartphone.

HOW TO RESTART WHEN STOPPED BY CO-MINDER (CO SHUT-OFF SYSTEM)

When the engine is automatically stopped by the CO-MINDER, move the 
generator to an area with fresh air and away from any device that may be 
emitting carbon monoxide, such as another generator. Press the CO-MINDER 
reset button and then follow the standard procedure for starting the engine. 
When the CO ALARM indicator or the FAULT/CO-MINDER LIFE indicator flashes, 
press the CO-MINDER reset button to turn off the indicator.
However, even if the CO-MINDER reset button is pressed and the CO ALARM 
indicator turns off, the engine cannot be started remotely using the remote 
control kit (optional part) or the 

Bluetooth

® connection unless the engine is 

started using the engine switch on the generator once.

When the remote control is connected, turn the MAIN switch on remote control to 
the ON position and then restart the engine. If the MAIN switch on remote control is 
in the OFF position, using the engine switch on the generator will crank the engine, 
but the engine will not start.

CO-MINDER RESET BUTTON

CO ALARM INDICATOR

FAULT/CO SENSOR LIFE 
INDICATOR

31Z236200.book  49 ページ  ２０２０年２月２０日　木曜日　午後１時８分

Содержание EM5000SX





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды