manualshive.com logo in svg

Honda EB10000, Руководство пользователя

Поделиться
Скачать
Honda EB10000 Скачать руководство пользователя страница 47

BEFORE OPERATION

45

4. Clean the filter elements if they are to be reused.

Paper filter element: Tap the filter element several times on a hard surface to 
remove dirt, or blow compressed air [not exceeding 30 psi (207 kPa, 2.1 kgf/
cm

2

)] through the filter element from the air cleaner case side.

Never try to brush off dirt; brushing will force dirt into the fibers. Replace the 
paper filter element if it is excessively dirty.

Foam filter element: If the foam filter is dirty, clean it as described on page 68. 
Replace the foam filter if it is damaged.

5. Wipe dirt from the inside of the air cleaner body and cover, using a moist rag. 

Be careful to prevent dirt from entering the air chamber that leads to the 
carburetor.

6. Place the foam filter element over the paper filter element, and reinstall the 

assembled filter element. Be sure the packing is in place beneath the filter 
element. Tighten the wing nut securely.

7. Lock the air cleaner cover latch securely.

8. Close the maintenance cover.

Operating the engine without the air filters, or with a damaged air filters, will allow 
dirt to enter the engine, causing rapid engine wear. This type of damage is not 
covered by the Distributor’s Limited Warranty.

31Z266200.book  45 ページ  ２０２０年２月２０日　木曜日　午前１１時１２分

Содержание EB10000

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды