Honda CRF300L Скачать руководство пользователя страница 34

Страница: 34 / 125

Average speed [AVG]

Displays the average speed since the selected

tripmeter was reset.

The average speed will be calculated based on

value displayed on the tripmeter (A or B)

selected.

Also, the average speed for tripmeter A will be

displayed when the odometer, tripmeter A, and

stopwatch are selected.

Display range:

ED type

0 to 199 km/h (0 to 124 mile/h)

Except ED type

0 to 199 km/h

•

Initial display: “---” is displayed.

•

When your vehicle has traveled less than 0.2

km (0.12 mile) since the engine was started:

“---” is displayed.

•

When your vehicle operating time is less

than 30 seconds since the engine was

started: “---” is displayed.

When “---” is displayed except for the above-

mentioned cases, go to your dealer for service.

To reset the average speed:

(

P.26

)

20200914163746_32K1TB000_eng_BOOK Page 34 Monday, September 14 2020 16:42:25 JST

Operation Guide

Continued

Содержание CRF300L






























































































































Результаты поиска

Содержание CRF300L

Отзывы:

Похожие инструкции для CRF300L

Бренды по названию

Популярные бренды

Honda CRF300L, Руководство пользователя

Результаты поиска

Содержание CRF300L

Отзывы:

Похожие инструкции для CRF300L

Бренды по названию

Популярные бренды