Honda CD Changer Скачать руководство пользователя страница 7

Страница: 7 / 10

AII 23268 (0110)

7 of 10

Installing the CD Changer

26. Carefully unpack the CD changer. Remove the

three shipping clips, and discard the shipping
cover. Save the shipping clips for your customer
in the event the unit needs to be serviced.

28. Visually check the location of the spring

adjusting pins on both sides of the CD changer.
If the spring adjusting pins are not in the vertical
(V) position, move the pins to the vertical (V)
position with a small flat-tip screwdriver.

29. Remove the backing from the two adhesive

covers, and attach one cover to each side of the
CD changer. Align the two diagonally opposite
holes with the H and V positions.

27. Install an adhesive seal (included with the CD

changer kit) over each of the three clip holes.

FOR VERTICAL
INSTALLATION

SPRING ADJUSTING PIN
VERTICAL POSITION

LEFT LOCKING
COVER
(supplied with
CD Changer kit)

RIGHT LOCKING
COVER
(supplied with
CD Changer kit)

30. Position the front and rear brackets on the CD

changer, and install four 4 x 8 mm washer-
screws into each bracket.

31. Using a utility knife, cut out the inside line of the

center area on the CD changer trim.

4 x 8 mm
WASHER-SCREW

Cut out.

REAR
BRACKET

CD CHANGER

FRONT
BRACKET

4 x 8 mm
WASHER-
SCREW

CD CHANGER
TRIM

OUTSIDE LINE
Do not cut here.

INSIDE LINE
Cut here.

SHIPPING CLIP

ADHESIVE SEAL

SHIPPING COVER
(Discard.)

Содержание CD Changer











Результаты поиска

Содержание CD Changer

Отзывы:

Похожие инструкции для CD Changer

Бренды по названию

Популярные бренды

Honda CD Changer, Руководство по установке

Результаты поиска

Содержание CD Changer

Отзывы:

Похожие инструкции для CD Changer

Бренды по названию

Популярные бренды