Honda CBR650F 2014 Скачать руководство пользователя страница 94

Страница: 94 / 133

Tire Puncture

Removing Wheels

ou
bles

hoo

ting

Install the right brake caliper and tighten
new mounting bolts.

10.

Install the left brake caliper and tighten
new mounting bolts.

Take care to prevent the brake caliper
from scratching the wheel during
installation.

Use new mounting bolts when
installing the brake calipers.

11.

Lower the front wheel on the ground.

12.

Apply the brake lever several times.
Then, pump the fork several times.

13.

Retighten the left axle pinch bolt.

14.

Raise the front wheel off the ground
again, and check that the wheel rotates
freely after you release the brake.

15.

Remove the protective tape or cloth.

If a torque wrench was not used for
installation, see your dealer as soon as
possible to verify proper assembly.
Improper assembly may lead to loss of
braking capacity.

Torque:

22 lbf·ft (30 N·m, 3.1 kgf·m).

Torque:

22 lbf·ft (30 N·m, 3.1 kgf·m).

NOTICE

When installing the brake calipers into position on the
fork legs, carefully fit the brake disc between the pads
to avoid scratching them.

Torque:

16 lbf·ft (22 N·m, 2.2 kgf·m).

Содержание CBR650F 2014






































































































































Результаты поиска

Содержание CBR650F 2014

Отзывы:

Похожие инструкции для CBR650F 2014

Бренды по названию

Популярные бренды

Honda CBR650F 2014, Руководство пользователя

Результаты поиска

Содержание CBR650F 2014

Отзывы:

Похожие инструкции для CBR650F 2014

Бренды по названию

Популярные бренды