manualshive.com logo in svg

Honda 2002 CBR150R, Руководство пользователя, Страница: 72 / 303

Поделиться
Скачать
Honda 2002 CBR150R Скачать руководство пользователя страница 72

5-6

FUEL SYSTEM

HOLDER

Remove the needle holder.
Remove the spring, jet needle and washer from the
vacuum piston.

Check the following:
— jet needle for stepped wear
— vacuum piston for wear or damage
— diaphragm for pin holes, deterioration or damage

NOTE:

Air can leak out of the vacuum chamber if the diaphragm
is damaged in any way, even if only a pin hole.

DIAPHRAGM/
VACUUM PISTON

CARBURETOR DISASSEMBLY

VACUUM CHAMBER

Remove the two screws and vacuum chamber cover.

NOTE:

As the compression spring is very long, it will jump out of
the carburetor when the cover is removed.

SPRING

Remove the compression spring and diaphragm/vacuum
piston from the carburetor body.

JET NEEDLE

DIAPHRAGM/VACUUM PISTON

SPRING

HOLDER

WASHER

COVER

SCREWS

Содержание 2002 CBR150R
















































































































































































































































































































Отзывы:

Нет отзывов