Honda 08W60-SVA-100 Скачать руководство пользователя страница 4

Страница: 4 / 9

4 of 9

AII 44382 (1008)

11. Install the wheel sensor harness clip and the

brake hose bracket to the damper.

12. With the suspension loaded with the weight of the

vehicle, torque the damper pinch bolts and the
self-locking nuts to 90 N·m (67 lb-ft), and torque
the upper flange nuts to 44 N·m (33 lb-ft).

13. Repeat steps 2 thru 11 to install the right front

damper.

14. Reinstall the service cap and the lid.

15. Reinstall the front wheels.

Removing the Rear Dampers

•

Remove the spare tire lid.

16. Lower the vehicle near the ground.

17. Remove the trunk side trim panel.

•

Fold each rear seat-back forward.

•

Pull back the front portion of the spare tire lid
and detach the clips.

SPARE
TIRE LID

DAMPER

DAMPER
PINCH
BOLTS

SELF-
LOCKING
NUTS

10. Loosely install new damper pinch bolts and new

self-locking nuts to the damper.

DAMPER

BRACKET
BOLT

WHEEL
SENSOR
HARNESS
CLIP

BRAKE HOSE
BRACKET

Содержание 08W60-SVA-100










Результаты поиска

Содержание 08W60-SVA-100

Отзывы:

Бренды по названию

Популярные бренды

Honda 08W60-SVA-100, Руководство по установке

Результаты поиска

Содержание 08W60-SVA-100

Отзывы:

Бренды по названию

Популярные бренды